HELP WHOEVER HAS DONE A B SERIES TRANNY
 

ALrighty i just got my part i needed in my tranny and started putting it together.... But when putting it BACK together.. i need to know how the lil springs are used when putting the case back together?.....i found a ball bearing that was not missing from any bearing cases in the tranny...my dad said that the bearing probably presses into the holes where the shift forks go up into the tranny?....He said the slots for the shift fork shafts have the have the long springs PRESSED into there holes with thte bearing on top so that the forks and ride on the ball?......IM VERY CONFUSING IM SURE.. but any help would be fukin AMAZING !!!!!!!!!!!! :y :y :y :y sorry guys.. I just need it done ASAP... cars been down for MONTHS....


Jordan

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

Ball - spring - bolt.

The ball and spring keep the shift forks in place. That's where the notch feel comes from when you shift.

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

I can say I've never done a tranny, it's not my thing.

But a factoy service manual would probebly be helpful:
http://hondatech.info/downloads/Auto/Manuals/Integra/

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

ok so i went back out in the frosty ------- cold and so the ball bearing DOESNT press in on top of the spring....how the ---- do you get the bearing to stay so that you can put the case back together???? is there a clip or something? i know u said spring-bearing-bolt but i dont see wher ea bolt is able to be used? ???

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

who took the tranny apart?

the BALL - SPRING - BOLT is the first thing you take out and the last thing you put in... once you put the two case halfs back together and bolt them down you put the ball, then the spring, and the bolt to hold all the ---- in into the two holes in the non-bellhousing part of the case...

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

So alrighty im a dumb ass.... :6 :y ANd i took those bolts out BUT!!!!!!!!!!!!!!!! i was never able to find the 2nd bearing that goes in one of them?????????????????????????????? AND in trying to look for it noticed a hair line crack alll the way across that very tip top bearing case on the smaller pillar of gears.. SOOOOOOOOOO now i have to find another bearing and get another " single" bearing for the spring.. WOW... i only got to drive the car maybe a week after i bought it......THIS BLOWS !!!!!!!!!

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

i have a hydro GSR tranny forsale ;) its already been put back together :P

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

whe you put that case back together you have a be so carefull to make sure everything is in place before you start torquind the bolts down because you will crack everything, I destroy my firt tranny I ever took apart, now I am somewhat well experienced in putting them back together.

1. you will crack the bearing on top that the snap ring fit into if you dont make sure the snap ring cleared out of the way of the bearing (use snap ring pliers)
2. if you dont make sure the shift forks are lined up, you will crack the upper housing
3 you will break the snap ring if its not cleared from the bearing.

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

HAHA A DAY TOO LATE !!!!!!!!!!!!!!.... :P :y FIRST THING I DID!!!!!!!!... the snap ring was cleared and everything but what i didnt know was that on the back side of the snap ring it wasnt 100% flush ANNNNNNNNNNNNNNNNNNNNND yup cracked that top bearing case.. nowwwww i have to get one of those...im sure u did the same with your first im guessing...Did you buy a new bearing or find a used one? and IF you did buy the new one what was the $?....My pops was saying to get the #'s off the bearing case and see if our local bearing shop would have it.... :-\

Re: HELP WHOEVER HAS DONE A B SERIES TRANNY
 

Oh hey and about that hydro GSR... i was reading that you can fab up a lil bracket to change it.. but how hard is it to ------ rig one of those up ? any right up's you know of from someone making there own ?..