|
Forged rods wont fit!!! help!!
I spun a bearing on my d16y7 running 6psi on a garrett t25. Now I am rebuilding the whole motor with new reinforce parts. New low compression pistons/rings, rod bearings, main bearings, and rods. The auction that i got the rods from stated that they work on d16 engines from 96-00. The problem is that the bottom of the rods wont fit into the cylinders without force. I dont want to scratch the freshly honed walls, so I dont want to force it. what should I do? are they the wrong rods?
|
Re: Forged rods wont fit!!! help!!
Originally Posted by d16y7sleeper
I spun a bearing on my d16y7 running 6psi on a garrett t25. Now I am rebuilding the whole motor with new reinforce parts. New low compression pistons/rings, rod bearings, main bearings, and rods. The auction that i got the rods from stated that they work on d16 engines from 96-00. The problem is that the bottom of the rods wont fit into the cylinders without force. I dont want to scratch the freshly honed walls, so I dont want to force it. what should I do? are they the wrong rods?
|
Re: Forged rods wont fit!!! help!!
How? the pistons are atached. and if t detach them how will I connect them again and have the rings stagered right?
|
Re: Forged rods wont fit!!! help!!
Is it safe to file down the sides of the rods a little? ???
|
Re: Forged rods wont fit!!! help!!
Originally Posted by d16y7sleeper
I spun a bearing on my d16y7 running 6psi on a garrett t25. Now I am rebuilding the whole motor with new reinforce parts. New low compression pistons/rings, rod bearings, main bearings, and rods. The auction that i got the rods from stated that they work on d16 engines from 96-00. The problem is that the bottom of the rods wont fit into the cylinders without force. I dont want to scratch the freshly honed walls, so I dont want to force it. what should I do? are they the wrong rods?
Originally Posted by d16y7sleeper
Is it safe to file down the sides of the rods a little? ???
|
Re: Forged rods wont fit!!! help!!
what parts are you using?
namely the rods.........link to the auction please....... |
Re: Forged rods wont fit!!! help!!
if them wont good then them arent correct rods for you engine.. :l
|
Re: Forged rods wont fit!!! help!!
here is the ink to the auction
http://cgi.ebay.com/ebaymotors/ws/eB...m=200025689505 one rod fits into cylinder #4 but catches about 3 inches down. the rest of the rods catch in the first 1/2 inch. |
Re: Forged rods wont fit!!! help!!
Originally Posted by d16y7sleeper
I spun a bearing on my d16y7 running 6psi on a garrett t25. Now I am rebuilding the whole motor with new reinforce parts. New low compression pistons/rings, rod bearings, main bearings, and rods.
|
Re: Forged rods wont fit!!! help!!
It wasnt the oil pump. It was my own stupidity because i didnt realize the gasket from my oil dump tube was leaking and the idiot light wire got disconected somehow. The oil pump seemed fine but i took it apart, cleaned it out and rebuilt it anyways just to be safe.
|
Re: Forged rods wont fit!!! help!!
so what rods are u using
|
Re: Forged rods wont fit!!! help!!
Originally Posted by Zeniceguycrx
so what rods are u using
Originally Posted by d16y7sleeper
here is the ink to the auction
http://cgi.ebay.com/ebaymotors/ws/eB...m=200025689505 one rod fits into cylinder #4 but catches about 3 inches down. the rest of the rods catch in the first 1/2 inch. |
Re: Forged rods wont fit!!! help!!
Originally Posted by d16y7sleeper
It wasnt the oil pump. It was my own stupidity because i didnt realize the gasket from my oil dump tube was leaking and the idiot light wire got disconected somehow. The oil pump seemed fine but i took it apart, cleaned it out and rebuilt it anyways just to be safe.
|
Re: Forged rods wont fit!!! help!!
replaced the gasket and all gaskets on the motor. just need to figure out the solution to the problem w/ the rods and I can put it back together.
|
Re: Forged rods wont fit!!! help!!
Originally Posted by Walter
if them wont good then them arent correct rods for you engine.. :l
|
Re: Forged rods wont fit!!! help!!
this happened with the tunertoys rods too, the first batch they had made wouldnt fit in the cylinder, they had to change the design, return them, and buy a TT set.
|
Re: Forged rods wont fit!!! help!!
the auction shows 5290 on the side of the rod...is that what yours say? because that would be .104" too short for a 1.6....
|
Re: Forged rods wont fit!!! help!!
If the rod goes down 3 inches and THEN gets stuck you have an egg shaped cylinder. Please try again.
|
Re: Forged rods wont fit!!! help!!
alot of those rods come from the same chinese manufacturer as the tt rods. my tt rods had to be shaved a cunthair each side to fit down the cylinder wallls.
|
Re: Forged rods wont fit!!! help!!
Originally Posted by CSaddict
If the rod goes down 3 inches and THEN gets stuck you have an egg shaped cylinder. Please try again.
|
Re: Forged rods wont fit!!! help!!
Originally Posted by JK_Motorsports
Or a taper was my first thought!!!!!
|
Re: Forged rods wont fit!!! help!!
http://search.stores.ebay.com/CRANKS...460423QQsofpZ0
what do you guys think about these rods? I just saw them on ebay. affordable f series rods are hard to come by. I wonder how good they are though. If I had the extra cash I'd buy them anyway. |
Re: Forged rods wont fit!!! help!!
Originally Posted by Walter
if them wont good then them arent correct rods for you engine.. :l
|
Re: Forged rods wont fit!!! help!!
i know ;D , ago long time i left to use the translator for to translate phrases.. at least i think jajonjon understood what i wanted to say ;D
Dmc1 do you bought them? did you fix the trouble already? |
Re: Forged rods wont fit!!! help!!
No not yet Walter. I'm selling some stuff on ebay so I can buy the rods and some pistons.
|
Re: Forged rods wont fit!!! help!!
didnt some one use a belt sander and a pen cap to make a hmt machine shop. i cant find a link but that sould work. id do both sides to try and keep it semi balanced
|
| All times are GMT -5. The time now is 01:55 PM. |
© 2024 MH Sub I, LLC dba Internet Brands