Anybody ever take a tranny apart? Hehehe I just did!
I'm practicing on a junk tranny. I'm really just curious and want to know how to install one of those Arizona Race LSD units. How the hell do I get the differential out? I have been ------- with this thing forever and can't figure out how to get it out.
http://pic4.picturetrail.com/VOL62/1...7/28370668.jpg http://pic4.picturetrail.com/VOL62/1...7/28370660.jpg http://pic4.picturetrail.com/VOL62/1...7/28370655.jpg http://pic4.picturetrail.com/VOL62/1...7/28370647.jpg How the ---- do I get this out? ??? http://pic4.picturetrail.com/VOL62/1...7/28370639.jpg http://pic4.picturetrail.com/VOL62/1...7/28370630.jpg __________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Re:Anybody ever take a tranny apart? Hehehe I just did!
:D Pretty fun huh Doc? I used to do that for a while. I'm not exactly sure how to remove it, but I know that most of the time theres a snap ring that holds alot of your parts in the tranny. you may need to rotate the gear so you can see it to get access to it. If there isn't one, you may need a pulling tool of some type to remove that bearing, then the gear should come off. Don't hold me to it, I'm just taking a guess, but let us know what happens man.
|
Re:Anybody ever take a tranny apart? Hehehe I just did!
take the shift things out. (royal pita.) u can slide the shafts out if you hit the main one with a hammer after u got the shift things off the gears.
as for getting the diff out. get a big ass crow bar and pop it out. it isnt pressed in there hard. just give it some stank. tip: to get the shift pins out loosen the little bolt that goes into the shift shaft near the diff then wack the groove with a chisel and spin it around. (warning, there are ball bearing and springs when u slide the shift pins out.. they will fly!) i took all the gears off mine but that was not nessesary now that i look at how the trani goes toghther. |
Re:Anybody ever take a tranny apart? Hehehe I just did!
Yeah, there was one of those snap rings holding the casing together. That was a bitch to get off. I don't know how I'm going to get it back on. It got pretty hot outside so I gave up on it for today. It's about 112 right now and I'm not about to go sit in the garage. :-\
__________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Re:Anybody ever take a tranny apart? Hehehe I just did!
Ok, I think I have an idea. After reading this: http://home.cinci.rr.com/mistab0ne/tranny.html I'm thinking about making myself a tranny. If these gears will work in the correct places I'm going to make one hell of a close ratio tranny.
Using these gears: EX/Si 1st-----3.250 2nd-----1.900 3rd-----1.250 4th-----0.909 5th-----0.750 for Si HB and Del sol Si or------0.702 for 2 dr or 4 dr sedan Final Drive---4.250 DX 1st-----3.250 2nd-----1.762 3rd-----1.172 4th-----0.909 5th-----0.702 Final Drive---4.058 I'm going to use an SI tranny. Keep the first gear and second gear. Swap the third with the DX second. Swap the fourth with the DX third and the DX fourth with the SI fifth and keep the SI final. This will give me an insane close ratio. My new gears would go like this: 1st. 35.2 MPH@7200RPM 2nd. 60.2MPH@7200RPM 3rd. ~70~MPH@7200 4th. ~90~MPH@7200RPM 5th. 124.5MPH@6800RPM My RPM would be a bit lower and the 3rd and 4th would be a bit off, but that's about what would happen. Now I just have to find out if they will fit. I'm pretty sure they will. Then on top of all that I would install a Twin-Trac LSD. :D What do ya think? __________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Re:Anybody ever take a tranny apart? Hehehe I just did!
Originally Posted by shortyz
take the shift things out. (royal pita.) u can slide the shafts out if you hit the main one with a hammer after u got the shift things off the gears.
as for getting the diff out. get a big ass crow bar and pop it out. it isnt pressed in there hard. just give it some stank. tip: to get the shift pins out loosen the little bolt that goes into the shift shaft near the diff then wack the groove with a chisel and spin it around. (warning, there are ball bearing and springs when u slide the shift pins out.. they will fly!) i took all the gears off mine but that was not nessesary now that i look at how the trani goes toghther. __________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Re:Anybody ever take a tranny apart? Hehehe I just did!
i fell stuiped asking this but no one has ever told me so whats the diff. in a close ratio and high ratio tranny
thanx |
Re:Anybody ever take a tranny apart? Hehehe I just did!
Close ratio would be more for racing. It will keep the engine in the upper rpm band where the power is. So instead of hitting 90+ in third I would be hitting 70 and get there WAY quicker. :)
__________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Re:Anybody ever take a tranny apart? Hehehe I just did!
cool. what about the ls 5th gear?
|
Re:Anybody ever take a tranny apart? Hehehe I just did!
I dunno? Would it fit? ??? That would be a pain to get a hold of. I already have an extra DX tranny that I can steal gears from. I don't have any ls trannies. :-[
__________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
All times are GMT -5. The time now is 11:26 PM. |
© 2024 MH Sub I, LLC dba Internet Brands