HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Hybrid/Tech (https://www.homemadeturbo.com/hybrid-tech-8/)
-   -   5G help...dx to ex (https://www.homemadeturbo.com/hybrid-tech-8/5g-help-dx-ex-18762/)

ZC4ME 04-11-2004 11:23 PM
5G help...dx to ex
 
Ok..I have been looking on/off all day and I cannot seem to find specifically what I am looking for. I have a friend that wants to go from a d15 to the d16z6 in his 94 hatch. I have been looking for info concerning the wiring for vtec and if he can use the existing intake/exhaust manifold, dizzy etc... Thanks in advance.

Dr.Boost 04-11-2004 11:31 PM
Re:5G help...dx to ex
 
If you wanted to make it really easy, you could just buy a VAFC and run VTEC from that, or you could run two wires to the ECU for VTEC and run a P28.

The intake and exhaust manifolds will fit.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote

ZC4ME 04-11-2004 11:46 PM
Re:5G help...dx to ex
 
Originally Posted by Dr.Boost
If you wanted to make it really easy, you could just buy a VAFC and run VTEC from that, or you could run two wires to the ECU for VTEC and run a P28.

The intake and exhaust manifolds will fit.
Cool, I am assuming that the P28 will be a direct plug in then? The dizzy and everything will be cool too? Are there any unused pins that I can graft over for the 2 added wires or will pins from a 4G harness work? Thanks again.

Dr.Boost 04-11-2004 11:49 PM
Re:5G help...dx to ex
 
The P28 will plug right into an OBD1 harness. The distributor might not be so easy. I don't think it bolts up right. You might have to rig something up with that one, but it will work. Not sure about the pins. I think you have to actually run the extra wires. I don't think there is anything you could swap around. I'm not sure about the pins being interchangable.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote

ZC4ME 04-12-2004 12:07 AM
Re:5G help...dx to ex
 
Originally Posted by Dr.Boost
The P28 will plug right into an OBD1 harness. The distributor might not be so easy. I don't think it bolts up right. You might have to rig something up with that one, but it will work. Not sure about the pins. I think you have to actually run the extra wires. I don't think there is anything you could swap around. I'm not sure about the pins being interchangable.
Yea, I figure that I would have to run the wires, but I thought there might be a couple of unused pins I could snatch out of the harness (like when doing an DPFI to MPFI conversion). If not I am sure I can hack a few wires out of a boneyard car. Hmmm, sounds like it would be best to just find the appropriate dizzy too. Thanks doc.

spooncivic1 04-12-2004 10:11 AM
Re:5G help...dx to ex
 
the dizzy bolts right up. we just did it on my friends car. from a b7 to a z6. make sure you get the right spark plug wires though.

OnYx 04-12-2004 07:15 PM
Re:5G help...dx to ex
 
you can chip that OBD 1 Po6 ecu to run VTEC and have ti chipped to run as a p28 for future mods, that runs about $100 in all (from me lol)

ZC4ME 04-12-2004 07:46 PM
Re:5G help...dx to ex
 
Originally Posted by onyx
you can chip that OBD 1 Po6 ecu to run VTEC and have ti chipped to run as a p28 for future mods, that runs about $100 in all (from me lol)
Cool, I just ordered a burner, two sockets and three chips last night from Moates.net because I want to run turbo edit for my set-up.


All times are GMT -5. The time now is 11:16 AM.


© 2024 MH Sub I, LLC dba Internet Brands