This Weekend at HMT, Lots a Pics..
Well, Beau started off this weekend by getting my new manifold built for My LS/Vtec. I must admit he is doing a very fine job for his first time for something like this. Here are a few pics of the manifold.
https://www.homemadeturbo.com/turbo/lsvtec/mana1.jpg https://www.homemadeturbo.com/turbo/lsvtec/mana2.jpg https://www.homemadeturbo.com/turbo/lsvtec/mana3.jpg It's very nice, all done in stainless, Not sure what the exact sizes are, and how many pieces he used... Beau is getting good with his new Tig welder. My batteries died on the digi camara, but its pretty much all finished now, Will get some more pics once its cleaned up. Saturday Night I got a Engine Swap setup for me and Beau to do, it was a basic ZC swap in a 90si crx. We took a few pics for the hell of it. https://www.homemadeturbo.com/tech/swap/zc1.jpg A very clean D16a6 https://www.homemadeturbo.com/tech/swap/zc5.jpg You can see the 2 differnt plugs for the ZC distributor, and the factory SI harness, Just showing for those people who dont belive me, their is some wiring involved, (cough Dustin) https://www.homemadeturbo.com/tech/swap/zc3.jpg Pops wanted us to do a clean install, So beau Busted out the sexy baby blue paint and painted up the manafold shield for our customer.. (LMAO) <--- yes beau you know what that means?!?!? ;) https://www.homemadeturbo.com/tech/swap/zc4.jpg We were never going to actually put the heat shield on the car, but we did decide that the Oil pan may rust (LOL) so maybe we should give it a thin coat of baby blue.. hahaha https://www.homemadeturbo.com/tech/swap/zc7.jpg We also tried a different way of pulling in and out of the motor, I wasnt really use to this style, I have always taking the tranny and engine out as a unit, But Beau has showed me the independent flat rate style ;) https://www.homemadeturbo.com/tech/swap/zc8.jpg Dont you hate those god damn stickers that are on the new radiator hoses that are a complete bitch to get off? Well I just got to excited picking them off, and decided to get them nice and wet. HAHAHAHAH! ;D (the big black hose) https://www.homemadeturbo.com/tech/swap/zc9.jpg Finally done, it took a bit longer than what we are use to, since we had to work out at the barn, and we had no motovation. But it came out very clean, and runs very nice. https://www.homemadeturbo.com/misc/barn/barn2.jpg This is are holding/storage shop, AKA "THE BARN" refabbed into a import race garage. This is where my Race car is stored. https://www.homemadeturbo.com/ride/90dx/coma2.jpg Beau made me take these pics, to show everyone how lazy I am. Yes, this is the Big bad boy Race ZC.. Look how fast it is. It needs some major work, it seems to have been used for parts more than anything lately.. :-\ Oh well, need to get a bit more money and the race car will be priority #1. Should be done in time for Race season... (the night before opening day of course) https://www.homemadeturbo.com/ride/90dx/coma1.jpg :-X Jeff Frank btw, I dont have a clue when the rest of the website will be done.... |
Re:This Weekend at HMT, Lots a Pics..
manifold is looking very nice!!!
what kinda tig did you get. those are nice machines! |
Re:This Weekend at HMT, Lots a Pics..
the manifold is done if jeff can find enough change in his couch cuchions he can buy some batteries for his camera and take more pics. I like the way it turned some of it just isnt as clean as i had expected.
Beau its just a small hobart tigmate |
Re:This Weekend at HMT, Lots a Pics..
BEau how much were those stainless pieces.
|
Re:This Weekend at HMT, Lots a Pics..
5.00 a piece for the 90s and i bought 4ft of straight at 8$ per. ft.
Beau |
Re:This Weekend at HMT, Lots a Pics..
Originally Posted by BLACKSI
5.00 a piece for the 90s and i bought 4ft of straight at 8$ per. ft.
Beau damn i wish i had your welding skillz how did you get that zc block so clean looking on that zc "race motor"? paint? lookssweet |
Re:This Weekend at HMT, Lots a Pics..
Oh I forgot to mention about when we were delivering the car, Beau was driving my car, and he decided to break my shift rod in half! (while power shifting of course)I had to drive the car about 5 miles in 2nd gear on 50mph roads.. Haha. (maybe we should call out a recal on the JB shiftlinkage?) ;)
Jeff Frank |
Re:This Weekend at HMT, Lots a Pics..
"Oh I forgot to mention about when we were delivering the car, Beau was driving my car, and he decided to break my shift rod in half! (while power shifting of course)I had to drive the car about 5 miles in 2nd gear on 50mph roads.. Haha. (maybe we should call out a recal on the JB shiftlinkage?)"
I was raping the ---- outta of it ;D Beau |
Re:This Weekend at HMT, Lots a Pics..
man i love your zc jeff. im really kinda sad about getting a B16....just because you proved that the engine has so much potential. but o well it is what it is!
Dane |
Re:This Weekend at HMT, Lots a Pics..
y0 beau iF i send you some money to make one of those manifolds for me how much much would oyu charge plus all the parts?
|
Re:This Weekend at HMT, Lots a Pics..
Nice guys! Really impressed with the manifold thus far ;) Beau, please fwd to me where you are picking those bends up at if it is from an online site... if it is a local supply store, then don't worry about it... we got those here.
One thing that is sort of interesting to me is that you guys aren't doing the swaps from the bottom... Shortly after i got done with my own car, i was introduced to the world of doing swaps from the bottom of the car, and i'll NEVER do it from the top again. These days my cherry picker gets used simply to move things, and to raise the car if the lift is unavailable... LoL. |
Re:This Weekend at HMT, Lots a Pics..
Oh we still do swaps like that, but at "The barn" we dont have a lift :(
On 5g and up civic/tegs its a peice of cake doing bottom swaps. All that lovely room. https://www.homemadeturbo.com/tech/lsvtec/lsv3.jpg When we did the LS/vtec on my car, that is how we did it. I do motor swaps on most Nissans and Kias that way as well. Jeff |
Re:This Weekend at HMT, Lots a Pics..
AAaaahhh... ok, was just checkin ;) LoL.
Coming from a "V8 world" growing up, i went in from the top on most everything until very recently... now i won't do it any other way than from the bottom ;D Blah... |
Re:This Weekend at HMT, Lots a Pics..
y0 jeFf can you ask beau how much it would cost if he made another manifold like that for me and i pay for all the parts? :o ???
|
Re:This Weekend at HMT, Lots a Pics..
This is his first manifold dude, I am sure lots of people will want to buy them, but these are early stages of development.. If they do become for sale, I will let you know..
Jeff |
Re:This Weekend at HMT, Lots a Pics..
mcmaster might have those. i know they have nomarl steel.
search Unthreaded Steel Butt-Weld Pipe Fitting mabey they have SS. i duno. |
Re:This Weekend at HMT, Lots a Pics..
ok yeah they got em
www.mcmaster.com go there and put in "Unthreaded Stainless Steel Welded Pipe - Schedule 40" in search. then hit catalog page. hope that helps! 7.71 |
Re:This Weekend at HMT, Lots a Pics..
Actually, that search you gave brought up nothing but straight-stock... but i found this:
http://www.mcmaster.com/param/asp/ps...+Pipe+Fittings Which led me to this: http://www.mcmaster.com/param/asp/ps...530&FT_148=921 I'm not sure if that last one is the dimensions that Beau used, but they're wanting $7.34 per bend. When you're talking about buying a bunch of bends at once, $2.34 extra per bend start adding up, which is why i'm interessted in knowing where he is getting his.. ;) Although you can get Schedule 10 for $5.28 per bend.... wonder if it would be thick enough to hold without cracking... hmmm. More experimentation needed ;D |
Re:This Weekend at HMT, Lots a Pics..
HIT THE GOD DAM CATALOG PAGE its above matching items.
that will bring up everything.. |
Re:This Weekend at HMT, Lots a Pics..
Chill out shortyz.... you don't need to pop a vein (or yell)... LoL... ::)
So i missed a button... Haha. |
Re:This Weekend at HMT, Lots a Pics..
Originally Posted by ComposiMo
Chill out shortyz.... you don't need to pop a vein (or yell)... LoL... ::)
So i missed a button... Haha. smoking up a big ass bowl of weed with me and KG ALRIGHT!! .. all the ladies say yeah yeah all your mo fucka's say a prayer and you gotta fight fair. u know what time it is TENCIOUS D TIME ---- YEAHHHHHHHHHHHHHHHHHH yeah yeah ok im better now. |
Re:This Weekend at HMT, Lots a Pics..
thats were I got them from, they are schedule 10 which is plenty thick for stainless, I can't rember the exact dimensions right off hand. The straight piece i just bought at our local steel co.
Guys I realy don't know if im going to be making these to sell im sure i'll make my self one, but I dont know about mass production. Beau |
Re:This Weekend at HMT, Lots a Pics..
Aaaaahhh.... for some reason i was thinking that you used Schedule 40... ah well, at least it isn't Schedule 80 (see the price for that ----?!?!?) :o
|
Re:This Weekend at HMT, Lots a Pics..
i want a turbo manifold like that.... :o
|
Re:This Weekend at HMT, Lots a Pics..
I'm gonna make a manifold like that...
as soon as I can get some flanges... -Henry |
Re:This Weekend at HMT, Lots a Pics..
Originally Posted by DJHankB
I'm gonna make a manifold like that...
as soon as I can get some flanges... -Henry :P everythings twice the price in canada it really sucks ass. |
Re:This Weekend at HMT, Lots a Pics..
jeff, is that mani for your race zc? i thought you were using that funky one that went off to the side?
|
Re:This Weekend at HMT, Lots a Pics..
naw dude thats for the LSVTEC he is using the wierd fucker for the ZC...
|
Re:This Weekend at HMT, Lots a Pics..
and how many cars does he have?
|
Re:This Weekend at HMT, Lots a Pics..
|
Re:This Weekend at HMT, Lots a Pics..
90 DX, 89 Si, and a Ford Conversion Van hahahaha....
|
Re:This Weekend at HMT, Lots a Pics..
so what would you guys pay for a manifold like this? im not saying im going to sell them just wondering what thier worth to you guys.
Beau |
Re:This Weekend at HMT, Lots a Pics..
Originally Posted by BLACKSI
so what would you guys pay for a manifold like this? im not saying im going to sell them just wondering what thier worth to you guys.
Beau |
Re:This Weekend at HMT, Lots a Pics..
"so what would you guys pay for a manifold like this? im not saying im going to sell them just wondering what thier worth to you guys"
Well, considering i paid close to $1100.00 for mine......... ;) Lets see the finished product... specifically close-ups of the collector (inside). I understand that the welds likely will be better in the next one's, but lets base this pricing opinion on this exact manifold. This is a very good question that even i am interested in hearing the answer to... hehe. -J |
Re:This Weekend at HMT, Lots a Pics..
I bet you could get 400-550 on ebay if you polished that fucker up and gave it a saucey title. Personally, I wouldn't buy one, because I can make on for cheaper and I really don't care how it looks. But if I did, then 400 would not be unreasonable
|
Re:This Weekend at HMT, Lots a Pics..
"Well, considering i paid close to $1100.00 for mine........."
wholly ---- thats alot of cash for a manifold what all came with it, askets/ new studs or was it just the manifold? I can tell you now that this thing is no were near as nice as yours espeacily the inside of the collector but hopfuly things will get better with time. Beau |
Re:This Weekend at HMT, Lots a Pics..
i'll give you a 150bucks and a Jumbo Jack (with cheese if your nice)...
|
Re:This Weekend at HMT, Lots a Pics..
i like them with cheese.
::) Dane |
Re:This Weekend at HMT, Lots a Pics..
Damn John! Mister Big Spender with that car! heheh =P
But it's a very nice manifold.. -H |
Re:This Weekend at HMT, Lots a Pics..
hey dustin ill be more than happy to kick you in the bean bag for 150.
Beau |
All times are GMT -5. The time now is 04:58 AM. |
© 2024 MH Sub I, LLC dba Internet Brands