HomemadeTurbo - DIY Turbo Forum
Page 2 of 2
1
2
Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   General Discussion (https://www.homemadeturbo.com/general-discussion-6/)
-   -   How's this bottom end look (no...it ain't about chicks) (https://www.homemadeturbo.com/general-discussion-6/hows-bottom-end-look-no-aint-about-chicks-25711/)

45psi 09-01-2004 12:25 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
Nissan

HMT-Admin 09-01-2004 12:27 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
Originally Posted by Kyle
if it is honda it would have to be gsr because it has oil squirters, but those don't look like any gsr oil squirters I've seen.
All Dohc Vtec hondas have oil squirters, not just gsr's

Turbo90Accord4DR 09-01-2004 01:16 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
Originally Posted by AbaZ
Originally Posted by Kyle
if it is honda it would have to be gsr because it has oil squirters, but those don't look like any gsr oil squirters I've seen.
All Dohc Vtec hondas have oil squirters, not just gsr's

and a gsr would have a crank gridle

HMT-Admin 09-01-2004 01:30 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
Originally Posted by Turbo90Accord4DR
Originally Posted by AbaZ
Originally Posted by Kyle
if it is honda it would have to be gsr because it has oil squirters, but those don't look like any gsr oil squirters I've seen.
All Dohc Vtec hondas have oil squirters, not just gsr's

and a gsr would have a crank gridle
ITR's gotem too ;) The b16 and b17 were the unlucky ones that didnt get them (and non vtecs)

Btw guys, thats hardly dirty. Cast iron blocks usually always look like that.

needahonda 09-01-2004 03:26 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
since you have the pan off pull off the rod caps and look at the bearings. then put in some new ones....rod and mains....0.2

45psi 09-01-2004 03:32 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
Originally Posted by AbaZ
Originally Posted by Turbo90Accord4DR
Originally Posted by AbaZ
Originally Posted by Kyle
if it is honda it would have to be gsr because it has oil squirters, but those don't look like any gsr oil squirters I've seen.
All Dohc Vtec hondas have oil squirters, not just gsr's

and a gsr would have a crank gridle
ITR's gotem too ;) The b16 and b17 were the unlucky ones that didnt get them (and non vtecs)

Btw guys, thats hardly dirty. Cast iron blocks usually always look like that.
A6 comes with a crank girdle right???

TekPhobia 09-01-2004 03:32 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
Yep, that's the 4AGZE bottom end. The last version of the motor. Oil squirters, forged everything, etc.

I don't think it looks too bad. Who knows how long it sat in a junkyard in Japan with oil in the pan.

This motor is praised for its neck snapping torque. It should make a for a nice sleeper in a 4-door 2400lb sedan.

I plan on slappin a turbo on and boostin the hell out of it. HKS makes a nice manifold for the GZE.


Thanks guys!

-Tim

Semnos 09-01-2004 06:50 AM
Re:How's this bottom end look (no...it ain't about chicks)
 
That bottom end looks good to me...I've seen worse ... like mines and the engine still runs with no problems...
Mine is clean now...some new oil cleaned it all up.


All times are GMT -5. The time now is 08:51 AM.
Page 2 of 2
1
2
Show 40 post(s) from this thread on one page


© 2024 MH Sub I, LLC dba Internet Brands