HomemadeTurbo - DIY Turbo Forum - How do my numbers look?

Page 3 of 3

Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)

- General Discussion (https://www.homemadeturbo.com/general-discussion-6/)

- - How do my numbers look? (https://www.homemadeturbo.com/general-discussion-6/how-do-my-numbers-look-27830/)

crxdan

10-10-2004 10:07 PM

Re:How do my numbers look?

150 psi too low for zc?

Guy-Fast

10-10-2004 10:21 PM

Re:How do my numbers look?

Should be gettin 180-190 on dohc zc that is very good condition. Same goes for most d series motors. 150 is signs of wear/tear on the motor. The importer I go through does not allow d series motors below 160 to be sold

juli0_bustamante

10-10-2004 10:54 PM

Re:How do my numbers look?

Quote:

Originally Posted by trebor_nordap

i'd rebuild that dohc before going back to a single cam. i might cost even less to rebuild it. plus if you use forged pistons and rods. you'll have a much stronger motor then a stock single cam. even a dohc with stock pistons and stock rods will be stronger than a single cams' internals. oh and i'd spray the block with degreaser and let it get hot while running w/degreaser on so it would clean it. that stuff works good when it's sprayed on a warm engine and then let the engine get hotter while the degreaser is on.

hey shut up1 i need another DOHC! :P

AgentMurdoc

10-11-2004 04:11 AM

Re:How do my numbers look?

Boost, ride it on down to SoCal and I buy that *trash* DOHC longblock of yours from yours for fiddy dollas ;)

bambooseven

10-11-2004 04:33 AM

Re:How do my numbers look?

I have a complete z6 head w/ mani. or an A6 mani bare. take your pic andmake an offer. ;D

Dr.Boost

10-11-2004 07:53 AM

Re:How do my numbers look?

Quote:

Originally Posted by bambooseven

I have a complete z6 head w/ mani. or an A6 mani bare. take your pic andmake an offer. ;D

I think I have it covered. I might still be interested in that head/manifold though. I might as well start a new collection of SOHC parts.

The only reason I was even running this motor was because it came with the car. I was planning on being stupid and blowing it up anyways. :-\

We'll have to figure something out with those steelies. However Julio and I decide to do the swap.....
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote

FooK	10-11-2004 08:17 AM

Re:How do my numbers look?

i have a z6 intake mani, all sensors, no injectors or fuel rail, even has a TB.

juli0_bustamante

10-11-2004 01:09 PM

Re:How do my numbers look?

Quote:

Originally Posted by Dr.Boost

Quote:

Originally Posted by bambooseven

I have a complete z6 head w/ mani. or an A6 mani bare. take your pic andmake an offer. ;D

I think I have it covered. I might still be interested in that head/manifold though. I might as well start a new collection of SOHC parts.

However Julio and I decide to do the swap.....

i thought you werent suppose to tell em what we do outside HMT... :P

projekteg

10-12-2004 05:47 AM

Re:How do my numbers look?

i think i jinxed myself doing that comp. test, the next day i think i broke some ringlands, prolly gonna do a leak down test today. hoping it's just the hg, but i don't think so.

All times are GMT -5. The time now is 01:41 AM.

Page 3 of 3

Show 40 post(s) from this thread on one page