HomemadeTurbo - DIY Turbo Forum
Page 3 of 5
1
2
3
4
5
Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   General Discussion (https://www.homemadeturbo.com/general-discussion-6/)
-   -   compression test results are in! (https://www.homemadeturbo.com/general-discussion-6/compression-test-results-38333/)

FooK 04-24-2005 04:21 PM
Re: compression test results are in!
 
Originally Posted by projekteg
Originally Posted by beerbongskickass
Hey your almost as fast as my stock d-series turbo... ;)
stock b16 turbo untuned with 2 dying cylinders = healthy, tuned, stock d series turbo, yes, i would say the two are about equal :-*
yeah right you're lying you blew it well after the track and you know it. :-*

its funny you always see these guys in engine management giving the solid, dont run hard untuned advice, yet we got kev here ripping the 1/4 miles n ---- untuned.

Spenser 04-24-2005 04:48 PM
Re: compression test results are in!
 
kevin, when can i come pick up my truck load of dvd players?

J-SMITH69 04-24-2005 05:19 PM
Re: compression test results are in!
 
my integra was trappin around 99-102 with 4 broken ringlands. not to mention i would make a new hole in the o-zone everypass

projekteg 04-24-2005 05:43 PM
Re: compression test results are in!
 
Originally Posted by FooK
yeah right you're lying you blew it well after the track and you know it. :-*

its funny you always see these guys in engine management giving the solid, dont run hard untuned advice, yet we got kev here ripping the 1/4 miles n ---- untuned.
na, i know i blew it the same night i finished it. i had no dp, so i couldn't put my wb in and i had some pretty healthy timing maps ;). the next morning i started it up and it smoked like a bitch out of the breather, but after that, only did it under boost and little bit at idle. i figured i just needed to change my pcv valve (why it would be smoking at idle). i'm gonna try to finish building my ls block within a months time, but i have some stock b16 pistons/rods here at the house, so i may just throw them in with a new set of rings until the b18 is done, not quite sure yet.

accordepicenter 04-24-2005 05:50 PM
Re: compression test results are in!
 
how much boost was this projeckteg?

rollmodel 04-24-2005 06:16 PM
Re: compression test results are in!
 
Originally Posted by projekteg
200 - 170 - 190 - 200
there you go, the compressions fixed... a simple typing error ;)

FooK 04-24-2005 06:59 PM
Re: compression test results are in!
 
Originally Posted by rollmodel
Originally Posted by projekteg
200 - 170 - 190 - 200
there you go, the compressions fixed... a simple typing error ;)
a deviation that far between cylinders still isnt good. 170-200, tsk tsk

SkunT 04-25-2005 07:18 AM
Re: compression test results are in!
 
dam kevin, at least you still made it into the 12sec club on 2 fucked cyl.


douspray 04-25-2005 08:48 AM
Re: compression test results are in!
 
standing with hat over heart, for a moment of silence for another lost soldier!

FooK 04-25-2005 01:52 PM
Re: compression test results are in!
 
Originally Posted by douspray
standing with hat over heart, for a moment of silence for another lost soldier!
that was gay.


All times are GMT -5. The time now is 05:28 AM.
Page 3 of 5
1
2
3
4
5
Show 40 post(s) from this thread on one page


© 2024 MH Sub I, LLC dba Internet Brands