chingro's project teg, update **INSTALL PICS INSIDE**
 

EDITED!!!!!!!!!!!, motor was installed, pics added below...
_______________
________________
well it's has been awhile since i post up in this b_tch.
Been lurking around just reading and all.

here is my car
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg

here my car besides Paperchase's 4door GSR....(same day i melted a piston)
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg

-----------------------
Update on my car....I melted a piston (lean out) last sunday (week ago), and since then i started my new build up.

I decided to go for the bigger 1.8L instead of staying with the B16.
So I got me a LS block w/crank that was fully cleaned, NEW Main & Rod bearings, new rings, a complete Engine seal/gasket kit from Acura,(only the oil pan gasket was not OEM). Block Guard, Pistons ( 10.8:1 CR ), Stock Rods.

Enjoy the pics

http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg




---
--------------------------------------
UPDATED WITH INSTALL
------------------------------

Special thanks to paperchase for helping me with the swap, We swaped out the motor without taking out TRANNY, AXLES, or SUSPENSION, we just put the front on two jack stands, and took the motor off tranny and lower it to the ground, and did reverse for new motor install. It took most of the day, but it turned out the car will not be running tonight. Reasons: B16 Timing belt was too small (tried to save money), so tomor i hitting up the dealer for a LS belt, and as you can see in one of the pics my home boy was making a list of all the parts needed to get car running. Just so i dont have to make multiple trips.


enjoy pics

http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/we...MXk1NDE%3D.jpg

Re: chingro's project teg
 

you must be dumb, your using a blockgaurd.... Why do you keep coming back?

Re: chingro's project teg
 

i have used one before with no problems...............i have heard the stories here about the gaurds, but i have never encounted a problem with them....so i keep using them.......

Re: chingro's project teg
 

nice going chingro. u should jus fill the block. it can actually handle boost. :: honda tech thumbz up ::


by the way, where are you located?

Re: chingro's project teg
 

This guy is a scammin ass faggot everyone be a dick to him

https://www.homemadeturbo.com/forum/...?topic=25504.0
https://www.homemadeturbo.com/forum/...?topic=18821.0

Re: chingro's project teg
 

I thought that name was familiar, this guy is a worthless piece of ----. Hopefully this guys car will be stolen, or if were lucky he will be burnt alive in a fiery crash. Die faggot die.

Re: chingro's project teg
 

I was wondering the same thing, everytime he comes back he gets flamed.

Re: chingro's project teg
 

more like hiding and letting the dust settle, coward

Re: chingro's project teg
 

daaaaaaamn! douche. >:D

Re: chingro's project teg
 

i sell a ton of items on HMT, and had two problems, and look how it turns out.... ::)
O0 glad to see the haters out there.....and one i scammed no one, both guys got either their money or parts....i dont have time, not effort so i dont need to go through the story again, so f- you :-*
keep flaming, it's the thing that fuels me to keep doing my shyt for yall hater's

-----------------------------
----------------------------

i just finish dropping my old motor out.....and i am about to start putting in the new setup, the car will not run till next week, becasue the head will be sent out to the machine shop for some work. 8)

later
chingro