Any specs on this turbo?
#1
Any specs on this turbo?
I checked its out and it said something about and rx-7 but I couldn't find and flow numbers. I also couldn't find the turbo in this configuration anywhere. I would appreciate any help with some info on this one. I think it has a .63 ar hot side.
#2
Re: Any specs on this turbo?
Here's what I did:
1. Opened the picture
2. Typed HT18S-2S in my favorite search engine (google)
3. Found tons of links
http://www.google.com/search?hl=en&q...=Google+Search
1. Opened the picture
2. Typed HT18S-2S in my favorite search engine (google)
3. Found tons of links
http://www.google.com/search?hl=en&q...=Google+Search
#3
Re: Any specs on this turbo?
there is an ongoing problem with these turbos where people simply cannot find flow charts for these. this from the rumor mill at rx7club. i have one on my car. its just... not stock.
i suggest sending it out to bnr turbochargers and hell work some good magic on it.
the turbine side has a different housing.
heres bnr's website. call him up.
http://www.bnrturbos.com/2ndGen.htm
i suggest sending it out to bnr turbochargers and hell work some good magic on it.
the turbine side has a different housing.
heres bnr's website. call him up.
http://www.bnrturbos.com/2ndGen.htm
#5
Re: Any specs on this turbo?
well..., at around 14 or so psi is the limit. at 10 to 12 psi is what normally people go for, but it pushes a good bit of air.
i have a bnr stage one, so that thing can top out at a good 300 or so wheel hp. this one should give you around 250 whp (or more) if your in an rx7.
it will stand up to allot of heat. so yeah. plus, keep in mind it has a regular already in the center section, so you dont need an oil pressure regulator for it. and another thing, the stock waste gate spring is at 5 psi.
i have a bnr stage one, so that thing can top out at a good 300 or so wheel hp. this one should give you around 250 whp (or more) if your in an rx7.
it will stand up to allot of heat. so yeah. plus, keep in mind it has a regular already in the center section, so you dont need an oil pressure regulator for it. and another thing, the stock waste gate spring is at 5 psi.
#9
Re: Any specs on this turbo?
Originally Posted by schwenk
I just measured the Inducer and Exducer.
In-1.6825in or 42.7mm and Ex-2.4820 or 63mm
What would this compare to? Any HP numbers out of this with the .63 ar exhaust side?
Thanks guys.
In-1.6825in or 42.7mm and Ex-2.4820 or 63mm
What would this compare to? Any HP numbers out of this with the .63 ar exhaust side?
Thanks guys.
#10
Re: Any specs on this turbo?
Looks like the turbo from the 12A turbo rotary. Rather a rare item. Either that or it's a regular S4 RX-7 HT-18 onto which someone has slapped a turbine housing that looks remarkably like the housing from the 12A turbo.
For a small displacement piston engine it's a good turbo. But it's much too small for any rotary (including the 12A). For rotary stuff don't even think of running a hotside smaller then .90. Anything with "T3" in the name is also generally too small for the rotary.
For a small displacement piston engine it's a good turbo. But it's much too small for any rotary (including the 12A). For rotary stuff don't even think of running a hotside smaller then .90. Anything with "T3" in the name is also generally too small for the rotary.
Thread
Thread Starter
Forum
Replies
Last Post
turboDA6
General Discussion
15
09-19-2009 03:36 AM
ProzacOverdose
Forced Induction
14
12-01-2007 12:39 AM