WHICH TURBO WILL SUIT MY REQUIREMENTS?
#1
WHICH TURBO WILL SUIT MY REQUIREMENTS?
I have been racking my brains and searching trying to find ou what tubo will suit my requirements but im still not sure.
Im after a turbo that spools quickly and can produce a reasonable amount of mid and top end power. Im after trying to acheive arount the 260 - 270hp mark at arount 10 - 11psi.
Can anyone point me in the right direction as to what might be the most appropriate turbo?
I was looking at the t3/t4E turbo from westcoast turbo but there are that many variations, im baffeld
The help is most appreciated, Thanks
Chris
Im after a turbo that spools quickly and can produce a reasonable amount of mid and top end power. Im after trying to acheive arount the 260 - 270hp mark at arount 10 - 11psi.
Can anyone point me in the right direction as to what might be the most appropriate turbo?
I was looking at the t3/t4E turbo from westcoast turbo but there are that many variations, im baffeld
The help is most appreciated, Thanks
Chris
#3
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
sorry, the spec of car is:
Honda Civic SIR-S eg6
B16A2
tubular manifold
2.5" downpipe
De-cat
Fuel pump
Fuel reg
Hondata s200
Rc550 injectors
26 x 6.5 x 2.5 intercooler
greddy bov
tial 38mm with 1 bar spring
stock block
Honda Civic SIR-S eg6
B16A2
tubular manifold
2.5" downpipe
De-cat
Fuel pump
Fuel reg
Hondata s200
Rc550 injectors
26 x 6.5 x 2.5 intercooler
greddy bov
tial 38mm with 1 bar spring
stock block
#4
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
I would'nt go smaller than a T3-A/R .60/.48. A good choice will be a T3-A/R .60/.63 or a T3/T4, etc.. The link below also has some very helpful information.
https://www.homemadeturbo.com/forum/...?topic=37464.0
https://www.homemadeturbo.com/forum/...?topic=37464.0
#5
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
I tell all my customers the same thing - depends on what you want to spend.
If you have lots of coin then a disco potato would be a good choice. They spool a lot quicker than the T series. Can`t rebuild them if they break.
I`ve done lots of B16`s in your performance range with T3/T04E 54 trim and stage 3 0.63AR turbine. Personally I find the stage 3 wheel is a little laggy for a B16 but I`m not 100% sure you will make your horsepower targets at that boost level with a straight T3 wheel.
-Michael
If you have lots of coin then a disco potato would be a good choice. They spool a lot quicker than the T series. Can`t rebuild them if they break.
I`ve done lots of B16`s in your performance range with T3/T04E 54 trim and stage 3 0.63AR turbine. Personally I find the stage 3 wheel is a little laggy for a B16 but I`m not 100% sure you will make your horsepower targets at that boost level with a straight T3 wheel.
-Michael
#7
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
a t3 super 60 will work good, even a straight .48/.60 t3 will work, both will spool quick and both can hold 10 psi 'till 8,000 rpm, the super 60 is much better though, and the super 60 will easily make 260 hp at 10 psi...
#10
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Originally Posted by 98redcavz24
1 bar wg spring + stock block= pop
Thanks Again