WHICH TURBO WILL SUIT MY REQUIREMENTS?
I have been racking my brains and searching trying to find ou what tubo will suit my requirements but im still not sure.
Im after a turbo that spools quickly and can produce a reasonable amount of mid and top end power. Im after trying to acheive arount the 260 - 270hp mark at arount 10 - 11psi. Can anyone point me in the right direction as to what might be the most appropriate turbo? I was looking at the t3/t4E turbo from westcoast turbo but there are that many variations, im baffeld The help is most appreciated, Thanks Chris |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
need more info.
car? engine? mods? cha-mone |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
sorry, the spec of car is:
Honda Civic SIR-S eg6 B16A2 tubular manifold 2.5" downpipe De-cat Fuel pump Fuel reg Hondata s200 Rc550 injectors 26 x 6.5 x 2.5 intercooler greddy bov tial 38mm with 1 bar spring stock block |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
I would'nt go smaller than a T3-A/R .60/.48. A good choice will be a T3-A/R .60/.63 or a T3/T4, etc.. The link below also has some very helpful information.
https://www.homemadeturbo.com/forum/...?topic=37464.0 |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
I tell all my customers the same thing - depends on what you want to spend.
If you have lots of coin then a disco potato would be a good choice. They spool a lot quicker than the T series. Can`t rebuild them if they break. I`ve done lots of B16`s in your performance range with T3/T04E 54 trim and stage 3 0.63AR turbine. Personally I find the stage 3 wheel is a little laggy for a B16 but I`m not 100% sure you will make your horsepower targets at that boost level with a straight T3 wheel. -Michael |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Thanks for all your help, its much appreciated
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
a t3 super 60 will work good, even a straight .48/.60 t3 will work, both will spool quick and both can hold 10 psi 'till 8,000 rpm, the super 60 is much better though, and the super 60 will easily make 260 hp at 10 psi...
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
1 bar wg spring + stock block= pop
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Originally Posted by 98redcavz24
1 bar wg spring + stock block= pop
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Originally Posted by 98redcavz24
1 bar wg spring + stock block= pop
Thanks Again |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Originally Posted by boosted_b16
a t3 super 60 will work good, even a straight .48/.60 t3 will work, both will spool quick and both can hold 10 psi 'till 8,000 rpm, the super 60 is much better though, and the super 60 will easily make 260 hp at 10 psi...
Thanks Again |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
damn with 3400 i could have my car running high 9's. with that amount of money you should be able to let your mind wonder in many diferent dirrections. on a 1 bar spring your looking at 14.7 psi when including fmic and couplings it ussually drops 1 psi so you should be pretty close. if you wanted 10-12 psi you should have gone with a lower spring and tunred up the mbc or ebc.
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
i think the super 60 runs around $550-600 USD.
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Originally Posted by 4g63t_EGMonster
damn with 3400 i could have my car running high 9's. with that amount of money you should be able to let your mind wonder in many diferent dirrections. on a 1 bar spring your looking at 14.7 psi when including fmic and couplings it ussually drops 1 psi so you should be pretty close. if you wanted 10-12 psi you should have gone with a lower spring and tunred up the mbc or ebc.
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Originally Posted by hackish
I tell all my customers the same thing - depends on what you want to spend.
If you have lots of coin then a disco potato would be a good choice. They spool a lot quicker than the T series. Can`t rebuild them if they break. I`ve done lots of B16`s in your performance range with T3/T04E 54 trim and stage 3 0.63AR turbine. Personally I find the stage 3 wheel is a little laggy for a B16 but I`m not 100% sure you will make your horsepower targets at that boost level with a straight T3 wheel. -Michael |
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
Disco Potato = GT28RS
|
Re: WHICH TURBO WILL SUIT MY REQUIREMENTS?
ooowwww right, i get yah. Probs should have done a search first before asking. I think it will be out my price range unfortunatly
|
All times are GMT -5. The time now is 01:55 PM. |
© 2024 MH Sub I, LLC dba Internet Brands