...NEW video...D15B VTEC T3 SETUP---NOW MY CLUTCH LOL
!?
04-07-2007, 09:45 PM
#12
3.0 BAR
Join Date: Mar 2005
Posts: 3,161
Re: LOOOOOK !!!! NEW VIDEO...NEW PROBLEM...D15B VTEC T3 SETUP
Originally Posted by PhilStubbs
sounds like a bad injector to me.
Just one? Sounds rich to me. Do you smell gas or no? To check for injectors just put them in the fuel rail and then point them to a bucket or whatever and have someone turn the key to "ON" and watch to see if they all prime well. That's an A6 and Jason had a Z6, but I don't know how big of a difference that's going to matter at idle.
JP
04-07-2007, 09:57 PM
#15
3.0 BAR
Join Date: Mar 2005
Posts: 3,161
Re: LOOOOOK !!!! NEW VIDEO...NEW PROBLEM...D15B VTEC T3 SETUP
Originally Posted by PhilStubbs
maybe 2, but at least 1 cylinder isnt doing anything maybe 2
Not doubting you, just questioing.
Originally Posted by Dmc1
Sounds like a bad burn or a bad chip job that things in limp mode. Check the chip addresses in your burner.
start in 008000
end in 00FFFF
for a 27sf512
start in 008000
end in 00FFFF
for a 27sf512
That's a pretty good call. Jumper it and check the CEL code. If it stays solid you know it's a bad burn. I had a chip in a ZIF socket that for some reason decided to go crazy and dog my car out really bad and all it needed was taken out then pressed back in with a little force. Worked fine (thank God, because that was a nightmare after the HG change) and now run no ZIF.
JP
04-07-2007, 10:10 PM
#18
1.0 BAR
Thread Starter
Join Date: Feb 2006
Posts: 226
Re: LOOOOOK !!!! NEW VIDEO...NEW PROBLEM...D15B VTEC T3 SETUP
OK....It's not on 3 cylinders because I pulled each wire off individually, it got worse every time...limp mode I think is right...this is what I have on my willem software
size & checksum 0xFFFF 0xF678
Shift & Pattern Adr A0 --> A15 0x008000
and when I'm done burning it says verified OK.
size & checksum 0xFFFF 0xF678
Shift & Pattern Adr A0 --> A15 0x008000
and when I'm done burning it says verified OK.
04-07-2007, 10:18 PM
#19
Guest
Posts: n/a
Re: LOOOOOK !!!! NEW VIDEO...NEW PROBLEM...D15B VTEC T3 SETUP
Originally Posted by PoweredT3A6
OK....It's not on 3 cylinders because I pulled each wire off individually, it got worse every time...limp mode I think is right...this is what I have on my willem software
size & checksum 0xFFFF 0xF678
Shift & Pattern Adr A0 --> A15 0x008000
and when I'm done burning it says verified OK.
size & checksum 0xFFFF 0xF678
Shift & Pattern Adr A0 --> A15 0x008000
and when I'm done burning it says verified OK.
I don't know how to use a willem burner though I think theirs a sticky about it or do a search it's been covered before. I only know how to use a batronix and a burn1
04-07-2007, 10:20 PM
#20
3.0 BAR
Join Date: Aug 2003
Location: NE-PA
Posts: 4,666
Re: LOOOOOK !!!! NEW VIDEO...NEW PROBLEM...D15B VTEC T3 SETUP
Make sure to erase the chip 2 times with a willem. My willem says it erases fine the first time, but when you go to verify it comes up with data still on the eeprom.
http://www.-------------/install/Willem-SST.htm has the write-up on how the willem software should be setup for burning sst27sf512's. Make sure you have it on pcb3 as well.
http://www.-------------/install/Willem-SST.htm has the write-up on how the willem software should be setup for burning sst27sf512's. Make sure you have it on pcb3 as well.
