My Setup
04-07-2003, 01:45 AM
#11
0.0 BAR
Thread Starter
Join Date: Dec 2002
Posts: 0
Re:My Setup
Ok I finished modifying the IC... Basically what I did was made it flow one way.... before it use to flow in from the top... go through the IC from the top half and flow out the Bottom half... and now it flows in from one side... and out the other... I cut out a hole big enough for a 2in PVC pipe... I stuck it together using fiberglass resin... on both sides... in and out.. then i cut out the divider on one end of the IC and capped one of the inlet holes using the peice that was cut out from the other end tank and 3 layers of fiberglass... it looks a bit rough but there are no leaks...
heres some pics of the finished product.
HKS eat your heart out...
heres some pics of the finished product.
HKS eat your heart out...
04-07-2003, 08:23 AM
#14
3.0 BAR
Join Date: Feb 2003
Posts: 9,089
Re:My Setup
Originally Posted by --------
theres an exhaust leak on the wastegate flange... guess im going to either buy the gasket monday at Road racing engineering... or have it welded shut... anyrecomendations on how to stop it from leaking
no one has that gasket... i went to autozone, kragen, pepboys, napa. and my local parts warehouse.. and no one has anything remotly close to it...
no one has that gasket... i went to autozone, kragen, pepboys, napa. and my local parts warehouse.. and no one has anything remotly close to it...
good luck. Setup looks primo!
04-07-2003, 09:34 AM
#15
1.5 BAR
Join Date: Feb 2003
Posts: 828
Re:My Setup
Did you say you drove it with no oil lines I hate to be the voice of doom and gloom, but you may have destroyed your turbo! If not you took years off its life, turbo shafts spin at 80,000 RPM and up, even a quick trip down the street and back is to much with out oil pressure to the bearings! A word on turbo longevity,1)Never shut down a hot engine after a run,there will be no oil pressure and the turbo will still be spining. 2)After you change you oil, unhook the coil and spin the motor over to get oil to the turbo before starting the car.3)Let your turbo warm up a bit befor you make boost. 4) Always break a new turbo in for 500 miles befor trying any serious boost(this does not apply to used salvage yard turbos). I hope your turbo is ok.
I hate to be the voice of doom and gloom, but you may have destroyed your turbo! If not you took years off its life, turbo shafts spin at 80,000 RPM and up, even a quick trip down the street and back is to much with out oil pressure to the bearings! A word on turbo longevity,1)Never shut down a hot engine after a run,there will be no oil pressure and the turbo will still be spining. 2)After you change you oil, unhook the coil and spin the motor over to get oil to the turbo before starting the car.3)Let your turbo warm up a bit befor you make boost. 4) Always break a new turbo in for 500 miles befor trying any serious boost(this does not apply to used salvage yard turbos). I hope your turbo is ok.
04-07-2003, 04:43 PM
#19
0.0 BAR
Thread Starter
Join Date: Dec 2002
Posts: 0
Re:My Setup
i dont know if i mentioned this... but i just drove it for what seemed like 15 secs.... pushed it out on to the street.... turned it on... and took off... then i turned the engine off and cruised it up the driveway and into the garage... the turbo didnt get hot or anything....
04-08-2003, 02:52 PM
#20
3.0 BAR
Join Date: Apr 2003
Posts: 2,260
Re:My Setup
Originally Posted by customcoach
A word on turbo longevity,1)Never shut down a hot engine after a run,there will be no oil pressure and the turbo will still be spining.
Anyone else heard this?
