Have a look at my D15B setup
#1
Have a look at my D15B setup
well hi guys i am new here to the site and have been reading through a lot of the topics for the past few months up until the other day when the site went down......anyway i registered today and just want some input on what you all think of my setup that will be going on my jdm D15B in my 94 coupe dx.
anything i should look into adding to this setup plz feel free to let me know, it is my first boosted car, but have done a years worth of research to get to where i am now..
-BMCracing.com turbo mani w/T3 and 38mm WG flange (on the way)
-garrett T3 60trim or super 60, still deciding (haven't purchased yet)
-Tial 38mm WG w/.6 bar spring
-jcwhitney custom 2.5" U-bends for IC piping and custom DP w/5 bolt flange
-custom hosing and clamps (local hardware store)
-JRC 6" FMIC (haven't purchased yet)
-TurboXS RFL BOV
-stealthmodperformance.com Oil feed/return kit
-Chipped P28 w/uberdata w/BBKA basemap
-plx-250 wideband w/software for laptop for tweaking this map (no dyno close by)
-moates.net Ostrich (haven't purchased yet)
-DSM 450cc injectors w/resistor pack (still need pack and clips)
-NGK 1 stage colder plugs
-Autometer Boost guage (havne't purchased yet)
-custom PCV catch can setup
-hd clutch (haven't purchased yet, any suggestions)
this is my daily driver and will be looking for ~190whp....
i think that is it....any comments feel free
thanks
-Brad
anything i should look into adding to this setup plz feel free to let me know, it is my first boosted car, but have done a years worth of research to get to where i am now..
-BMCracing.com turbo mani w/T3 and 38mm WG flange (on the way)
-garrett T3 60trim or super 60, still deciding (haven't purchased yet)
-Tial 38mm WG w/.6 bar spring
-jcwhitney custom 2.5" U-bends for IC piping and custom DP w/5 bolt flange
-custom hosing and clamps (local hardware store)
-JRC 6" FMIC (haven't purchased yet)
-TurboXS RFL BOV
-stealthmodperformance.com Oil feed/return kit
-Chipped P28 w/uberdata w/BBKA basemap
-plx-250 wideband w/software for laptop for tweaking this map (no dyno close by)
-moates.net Ostrich (haven't purchased yet)
-DSM 450cc injectors w/resistor pack (still need pack and clips)
-NGK 1 stage colder plugs
-Autometer Boost guage (havne't purchased yet)
-custom PCV catch can setup
-hd clutch (haven't purchased yet, any suggestions)
this is my daily driver and will be looking for ~190whp....
i think that is it....any comments feel free
thanks
-Brad
#2
Re: suggestions on my setup
sounds pretty good,dont underestimate how much work it really is though, sounds like for once someone did some research befor just posting, HOW DO I TURBO? WHAT IS TURBO? UBER HUH? CHIP THE WHAT? A VAFC??WHAT TURBO? MISSING LINK? .....but that set up should easily get you to your hp goals if not a little better, for the clutch i have a clutchmaster stage 3 and its great, although i have a clutchmaster flywheel as well.......good luck!
#3
Re: Have a look at my D15B setup
thanks...... i have done alot of reading and stuff but am still uncertain abotu the best bang for buck clutch. the CM stage 3 is probably out of my reach right now..... any comments on the exedy stage 1?
will i need to resurface my OEM flywheel or will it be ok?
will i need to resurface my OEM flywheel or will it be ok?
#5
Re: Have a look at my D15B setup
so i guess the ACT or something would be about the best for the buck then hey??
http://cgi.ebay.com/ebaymotors/ws/eB...category=33730
or maybe XTD
http://cgi.ebay.com/ebaymotors/ws/eB...category=33730
any comments on those 2??
thanks
http://cgi.ebay.com/ebaymotors/ws/eB...category=33730
or maybe XTD
http://cgi.ebay.com/ebaymotors/ws/eB...category=33730
any comments on those 2??
thanks
#7
Re: Have a look at my D15B setup
I have the exedy stage1, it holds the boost, but its nothing to brag about...
I wouldnt use it to do any drag racing or anything like that, but for around town, its perfect.
and what do you mean by custom catch can set-up?
I wouldnt use it to do any drag racing or anything like that, but for around town, its perfect.
and what do you mean by custom catch can set-up?
#9
Re: Have a look at my D15B setup
I have the XTD stage 1 (for a 92-95)... when I bought it I didn't have too high of hopes for it since I never heard of the brand before, but I have to admit I really do like it a lot (compared to stock HF at least). I installed that with a ZEX 7lb flywheel in an Si transmission along with my D15B and I really like the feel of it, very strong.
But I am still NA so I have no idea how it will hold up to the extra power from boosting it.
But I am still NA so I have no idea how it will hold up to the extra power from boosting it.
#10
Re: Have a look at my D15B setup
i bought a clutch specialties sprung for my d16z6.. havent installed yet.// but many other ppl on here have nothing but good things to say about it.. and i was told i dont need to have my flywheel resurfaced... the disc will do it.. as long as theres not heatspots on it.. u can use your stock one..
as for injectors.. i went with brand new correct inject 450's from stealthmode.. for 200 dollars..
instead of buying used dsm 450s and having to do redo all the wiring.. plus who knows if the dsm's are clogged or what.. so i just got the ones from stealth that just plug n play.. and are brand new w/ warranty
as for injectors.. i went with brand new correct inject 450's from stealthmode.. for 200 dollars..
instead of buying used dsm 450s and having to do redo all the wiring.. plus who knows if the dsm's are clogged or what.. so i just got the ones from stealth that just plug n play.. and are brand new w/ warranty