Ford Probe 2.2 Turbo at Junkyard
#12
Re: Ford Probe 2.2 Turbo at Junkyard
Well my engine supposedly only has a redline around 5000 RPM so I won't be revving it very high. Yes boost in the 2500-5000 RPM range would be ideal for my setup and goals. But anyway I went ahead and pulled the ---- off today. I got Turbo, Manifold, DP, Intercooler, and Injectors for $100 and since I don't need the injectors I can seel them on ebay for hopefully $35 or so and then sen the manifold for maybe $15 so I should only be into this project $50. The turbo is in good shape with no shaftplay, spins beautifully, and no cracks that I have found. Now I need to get a manifold fabbed, oil lines and stuff, maybe a bigger inject with fuel tuning on the ecm, and then get a 3" exhaust made. I'm thinkin just going 3" straight pipe. I'll have pictures up tommorow.
#13
Re: Ford Probe 2.2 Turbo at Junkyard
be careful going too big on the exhaust, those little IHI like to spike, the bigger the exhaust the more they seem to spike, 2.25" or 2.5" would be plenty big, I think the factory Probe turbo only had 2" or maybe 2-1/8"
Neil
Neil
#15
Re: Ford Probe 2.2 Turbo at Junkyard
You guys are funny saying that the VJ11 is too small when I dynoed about 100 hp more than any of your Honda's with the same turbo on 16 psi. It's an excellant entry level turbo. The RHB5 VJ11 only has an exhaust side A/R of .27
The turbine has an exducer diameter of 42.40 mm and a inducer of 51.80 mm making it a 67 trim turbine.
The compressor side has an inducer of 36 mm and an exducer of 52.50 mm making it a 47 trim.
You also have the option of upgrading the compressor housing and wheel from the Warner Ishi/IHI from the 87-88 T Bird.
If you need rebuild advice, click here: http://www.mx6.com/forums/showthread.php?t=102559
Info on the hybrid is here: http://www.mx6.com/forums/showthread.php?t=129439
BTW- those injectors are 360cc injectors at their peak, they're high impedance as well.
73-90cc/15sec
The turbine has an exducer diameter of 42.40 mm and a inducer of 51.80 mm making it a 67 trim turbine.
The compressor side has an inducer of 36 mm and an exducer of 52.50 mm making it a 47 trim.
You also have the option of upgrading the compressor housing and wheel from the Warner Ishi/IHI from the 87-88 T Bird.
If you need rebuild advice, click here: http://www.mx6.com/forums/showthread.php?t=102559
Info on the hybrid is here: http://www.mx6.com/forums/showthread.php?t=129439
BTW- those injectors are 360cc injectors at their peak, they're high impedance as well.
73-90cc/15sec
#16
Re: Ford Probe 2.2 Turbo at Junkyard
its too small for alot of the stuff people are doing on here... most people are trying to make 220 hp or so at 7500 rpm+ or nearly 300hp on some b series spinning to 8500, you will def run out of flow with it in those situations, but using it on a truck should work pretty good, itll spool right off idle and get you boosting and adding power right where you need it, should work fine.
Thread
Thread Starter
Forum
Replies
Last Post
superjunprelude
Forced Induction
11
09-06-2005 12:04 AM