Finally finished my setup, take a look, lots of pics
27 Attachment(s)
My turbo project is underway, here is the setup…..
D15b7 in a 93 Del Sol Teo4h turbocharger, from a Chrysler in a junkyard VX manifold Stealthmode oil lines Homemade adapter plate, pretty badass if I might say so myself (pics below) DSM blue top 450’s OBD1 chip kit Willems Enhanced programmer Xenocron Data Cable DSM 1g intercooler Greddy knockoff type-rs bov Home depot catch can Faze boost gauge Charge piping- 2” EMT conduit/radiator hose/home depot couplers Spark plugs Custom 2 ½ exhaust PLX-M300 wideband Last but not least my donation and BIG THANKS to HMT I’m sure I missed some stuff too Here’s the Project…. First I started off with a riced out 93 del sol with a d15b7, 100,000 miles (I wish I could take all the money I stuck in the show and turn it to go) Attachment 32736 I went junkyard shopping, Picked up a HF mani, and a turbo off an old Chrysler, it’s a teo4h, small but good size for the b7. Attachment 32737 Attachment 32738 My next step was to mate the two together, this is where my homemade adapter plate comes in, I started out with a ½ piece of plate steel, traced out the flanges, finagled them together till they looked like they were in a good spot, traced them out, and started cutting. I then drilled and tapped holes in each side and welded in threaded rod. Attachment 32739 Attachment 32740 After the adapter plate was finished, the downpipe needed to be made, I wanted to save some bank but still wanted a decent downpipe so I decided to go at it HMT style, Bought some straight pieces from work (advance auto parts) and went to town with the grinder and welder. This was so akward to make because the flange on the turbo is not round but more oval shaped, it turned out very good in the end. I also made the flange myself out of ½ plate steel. Attachment 32741 Attachment 32742 Yes the pic is not fooling you, the downpipe is like 6 feet long, But I did weld a flexpipe section in. I welded in a second o2 bung right behing the flexpipe section Attachment 32743 Attachment 32744 I then setup my oil lines, I purchased from stealthmode, they went on so nice its not even worth piecing together a cheap set yourself. Dropped and tapped the oil pan also. I didn’t even end up using the drain that came with the kit, the drain that was on the turbo saved me from kinking or running my drain uphill. I also just tapped into a coolant line and ran it through the turbo. Attachment 32745 Attachment 32746 Attachment 32747 The charge piping consists of homemade depot couplers, radiator hose, and 2” EMT electrical conduit. I sidemounted a 1g dsm intercooler, fits real nice. Attachment 32748 Attachment 32749 For the management, I used 450cc dsm injectors, homemade resistor box, chipped p06 ecu, and a plx m-300. I am tuning with Crome and datalogging with EcuControl. Attachment 32750 I used a dremel and put the injector seals in a socket to bore them out so the 450’s fit inside them snug Attachment 32751 This is my buddy jake helping me make the resistor box Attachment 32752 Attachment 32753 Here is the resistor box installed, I know you love the sexy green electrical tape, its all I had to use at the time. Attachment 32754 I chipped and installed the data cable, not a bad job for a first timer if I say so myself Attachment 32755 Who would’ve knew installing a boost guage could be so much work, turned out real nice though. Attachment 32756 Attachment 32757 I used these clips on pin d14 on my ecu so I can switch back and forth from my stock o2 to my wideband Attachment 32758 My catchcan is one I made using a writeup I found here on hmt, its made from parts from home depot. I gutted out my pcv, and just ran it from the pcv to a barbed fitting I screwed into the air filter. I believe this is right, if you think it should be different let me know. Attachment 32759 Here is some pics of the finished setup, Its currently boosting at 5lbs, im waiting on a boost controller, will prolly run 10-12 (think it should be ok with this small of a turbo, tell me what you think), currently in the tuning process. Thanks to dave (leed) for the basemap ( it’s a little lean but pretty close), and a HUGE thanks to HMT, I couldn’t have done it without this site, WHERES MY DAMN STICKERS?!?! Attachment 32760 Fun cant last forever Attachment 32761 Heres a pic of my dad, he helped me out a lot on the downpipe and adapter plate. Attachment 32762 The car is now sitting, two days of being boosted and I lost my liscense, guess it gives me some time to get it tuned before beating on it, I will post some vids when I can. Thanks HMT and who’s in charge of the stickers? I donated like a month ago and haven’t heard anything back yet. |
Re: Finally finished my setup, take a look, lots of pics
SOLID hmt work! you're going to hate that te04h in about 2 days, doesnt make power for ----. im glad i got rid of mine
did you get a ticket? |
Re: Finally finished my setup, take a look, lots of pics
the pic of me pulled over was for not having a front liscense plate, I lost my liscense because I got too many underage drinking tickets
Edit: I know the teo4h is small but I cant risk destroying my motor just yet, this project left me broke. |
Re: Finally finished my setup, take a look, lots of pics
Damn good setup.
|
Re: Finally finished my setup, take a look, lots of pics
That is a nice job.Looks like you pay attention to detail and make a attempt at keeping it clean.Solid work and good luck getting your license back that must really hurt after all that work.
|
Re: Finally finished my setup, take a look, lots of pics
|
Re: Finally finished my setup, take a look, lots of pics
Yeah, i've been working on putting this project together for about a year, the day after I finish I get a letter in the mail, talk about irony.
|
Re: Finally finished my setup, take a look, lots of pics
Oh yeah, BTW, where are my damn stickers?!
|
Re: Finally finished my setup, take a look, lots of pics
nice work, all my dad does is stands around and tells me my shits gonna blow up :P
|
Re: Finally finished my setup, take a look, lots of pics
Originally Posted by djfob
nice work, all my dad does is stands around and tells me my shits gonna blow up :P
|
All times are GMT -5. The time now is 11:38 PM. |
© 2024 MH Sub I, LLC dba Internet Brands