dsm 450 injector install
 

ive been searching google and i searched all over here cant find a good dsm 450 injector install how to i got obd1 i know i have to dremel my intake a little bit dont know how to do the wiring can someone help me out thanks

Re: dsm 450 injector install
 

1 Dremel SEALS that go into intake mani....just a little bit
2 bolt in injectors
3 wire in a resistor box or 10 watt 10 ohm resistors
4 burn chip to run 450cc injectors
5 wack off because you have 450cc injectors

Re: dsm 450 injector install
 

you'll also have to cut the tabs out of the injectors for the obd1 clips to fit.......can't seem to find the write up on HT that I used

Re: dsm 450 injector install
 

hypothetically speaking of course, lets say you lost your seal(s) and just put the injectors in without them whats the worst that can happen? :'(

Re: dsm 450 injector install
 

you could get a check from the insurance company to pay for your burnt up car.

Re: dsm 450 injector install
 

First you'll smell a little gas then shortly thereafter you'll smell burning flesh. Yours.

Re: dsm 450 injector install
 

man i cant find a write up anywhere
1ok
2ok
3 dont know how to wire it up what about the resistor box from an older integra?
4 afc
5 done

Re: dsm 450 injector install
 

I'm pretty sure any Honda resistor box will do...

There are a few different ways to do it. I wired mine up through the wires near the shock tower (don't remember what it's called)...

I'll see if I can find a write up for you really quick, rather than explaining it myself...

Okay, here's the one I followed... make sure you test the continuity and go by that, don't just follow the Hondata site, my car was different!

http://www.honda-tech.com/zerothread?id=517274

Re: dsm 450 injector install
 

Re: dsm 450 injector install
 

yeah i forgot about modifying the clips...damn. But as far as the resistors go you can follow the injector plugs yellow wire with a black stripe. Just wire a radio shack resister inline with this wire and your good do go. I hear the resisitor pack looks nicer but if you do a nice organized job with the resisitors it will look good too.

Re: dsm 450 injector install
 

i prefer the resistor box.
https://www.homemadeturbo.com/forum/...9608#msg349608

Re: dsm 450 injector install
 

what do you mean about using a drimmel on the injectors? what do you need to drimmel?? pref an mspaint pic please ;)

Re: dsm 450 injector install
 

I didn't use a dremel on mine, I just used a sharp knife... I'll try to draw a picture reall quick... it's a small tab on the inside of the clip...

Re: dsm 450 injector install
 

Although i have mad sicc ms paint skills i dont have time right now. Basically sand down the inside of the seal where the injectors slide in and make it a little bigger. Just have a 450cc injector with you when you do this so you can test for a snug fit and keep sanding till you get there.

Re: dsm 450 injector install
 

Okay, as far as the clips go, here's what you have to modify...

This is a super fantastic drawing of an injector, DSM 450 if you couldn't tell, showing the part you have to shave off so it works with the stock clips...

https://img.photobucket.com/albums/v...ilcox1/dsm.jpg

Good thing I'm bored right now...

Oh, and you have to bore out the seals, but that's so self-explainatory it doesn't deserve a super fantastic drawing...

Re: dsm 450 injector install
 

so im shavin off a little tab off the clips? im still confused, haha, i just dont wanna fuckup my injectors

Re: dsm 450 injector install
 

you shave that little bump ON the injector itself.

Re: dsm 450 injector install
 

cut them till they fit, end of story

Re: dsm 450 injector install
 

You don't have to modify the clips... just shave the circled tab off the actual injector...

If you had the clips and injectors in your hands, it would be pretty obvious what part you need to modify... you won't mess up your injectors by doing this, it's nothing but a plastic tab that you have to remove..

Re: dsm 450 injector install
 

this thing? (sorry pics kinda blurry)

[img width=600 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODg2MzMyNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]

Re: dsm 450 injector install
 

^^^ yes

Re: dsm 450 injector install
 

i cant read what that says

Re: dsm 450 injector install
 

nevermind that pic too smalll but thanks looks easy just i never did it but im sure i could thanks guys did anyone run into any problems doing them before?

Re: dsm 450 injector install
 

now if i do step 5 first, and id rock it another time after step 3, am i still gonna be ok?

Re: dsm 450 injector install
 

it might work but dont forget what step you were at if you have to take a break because then you might get distracted and decide to go wack off again and then youll never finish(installing the injectors)

Re: dsm 450 injector install
 

what?

Re: dsm 450 injector install
 

ok good i pretty sure i could get them in with no problem now i need to find a write up on a mini me