Anyone fabricate their own control arms?
#21
Re: Anyone fabricate their own control arms?
Thanks for (most) of the replies guys. I was hoping to integrate camber adjustment into the UCA itself.....hence the reason to fab my own. JD I may end up going the nylon bushing route if all else fails. Last I was in Paul was busy as hell. No shortage of work for that man.
Any leads on the nylon? I have a sheet of 1" "something" that may work. I'm really not sure what the hell it is. It's certainly a higher durometer rating than Energy Suspension bushings though.
I've been made aware that www.bakerprecision.com has a wide variety of rod ends also. Some extremely high quality.
If anyone reads this whom has experience fabrication control arms feel free to chime in and post some pics.
Any leads on the nylon? I have a sheet of 1" "something" that may work. I'm really not sure what the hell it is. It's certainly a higher durometer rating than Energy Suspension bushings though.
I've been made aware that www.bakerprecision.com has a wide variety of rod ends also. Some extremely high quality.
If anyone reads this whom has experience fabrication control arms feel free to chime in and post some pics.
#23
Re: Anyone fabricate their own control arms?
Originally Posted by Joseph Davis
Ground Control sells HondAcura coilover kits on special for $275 occiasionally. At $50/spring, plus the $40-50 to get the cheap eGay coilovers, it makes more sense to buy a threaded perch that isn't prone to cracking. FYI, GC and most everyone else sells the generic design Eibach or Carrera springs $50/per. *shrug*
I have had three sets of egay coilovers, not one has had any problems. I can see a problem with most sleeves though. The stock shock doesn't have an ideal place for the sleeve to rest on. Hit it hard enough and it will slide down and split.
They have raised their prices since I last checked. They are at $55/coil. A year or so ago they were less than $40.
Oh well.
#25
Re: Anyone fabricate their own control arms?
Originally Posted by rudebwoy
wouldn't it cost more to fabricate control arms than to buy some from ebay?
Yes, I got some Rhino upper control arms for $70 shipped on egay. Identical to the skunk2 pro, but w/o the sticker.
#27
Re: Anyone fabricate their own control arms?
Originally Posted by Heath
Any leads on the nylon?
Originally Posted by rudebwoy
wouldn't it cost more to fabricate control arms than to buy some from ebay?
#28
Re: Anyone fabricate their own control arms?
Originally Posted by Joseph Davis
If these are simple bar type UCAs like found on Civic/Integra, then swaged steel tube with quality heims would run less than the $70 somebody mentioned. Also dead-nuts simple, and a bolt together affair with no fabrication.
$70 for both sides? Unless you can get some serious hookups.
4 - Quality Heim Joints
4 - Swedged Steel Bars
2 - Ball Joints
2 - Collars
2 - Clevis Joints
From speedwaymotors all that is gonna run a lot. They sell pre-built ones for $75 each though. With ball joints comes to almost $90 a side.
BUT, you would have completely adjustable arms. Caster & camber.
JD, what do think you could get all those parts for$ ?
#29
Re: Anyone fabricate their own control arms?
Huh?
I repeat:
Four quality heims, four locknuts, two swaged tubes will do both rear UCAs on a Civic/Integra.
I repeat:
Originally Posted by Joseph Davis
If these are simple bar type UCAs like found on Civic/Integra
#30
Re: Anyone fabricate their own control arms?
Originally Posted by Joseph Davis
Huh?
I repeat:
Four quality heims, four locknuts, two swaged tubes will do both rear UCAs on a Civic/Integra.
I repeat:
Four quality heims, four locknuts, two swaged tubes will do both rear UCAs on a Civic/Integra.
You didn't mention "rear" UCAs in your post.
Originally Posted by Joseph Davis
If these are simple bar type UCAs like found on Civic/Integra, then swaged steel tube with quality heims would run less than the $70 somebody mentioned.Also dead-nuts simple, and a bolt together affair with no fabrication.
As for rear UCAs, washers and longer bolts work wonders. $3 at your local hardware store.