vtec on my B16
Ok so I have a chipped P06 with vtec but I have yet to hook up my 02 sensor so it's throwing an 02 code. I ran the vtec solenoid wire to the ecu and now I have a rev limit of 6500 and no vtec, is this because of the o2 code?? Once I fix that will I be all set?
|
Re: vtec on my B16
Yes. You could also disable your O2...
|
Re: vtec on my B16
I disable 02 in uberdata and it still throws the code :-\ Going to toss an 02 in now.
|
Re: vtec on my B16
No codes, hooked up an 02, no vtec, rev limit still at 6500. This is a vtec p06 done by a guy who knows what he's doing. Is something wrong in uberdata? That's all I can think of. If the ecu is good, and there aren't any codes... I don't need vtec coolant check or any of that right? I just have ELD, PA sensor, and vtec the only things that are checked...
|
Re: vtec on my B16
Does a B16A3 have a vtec oil pressure switch?
|
Re: vtec on my B16
Yeah but I thought in uberdata you only needed to wire the single wire for vtec solenoid since the p06 isn't looking for vtec oil pressure.
|
Re: vtec on my B16
Alex send me your .bin
|
Re: vtec on my B16
Originally Posted by nonvtec
Yeah but I thought in uberdata you only needed to wire the single wire for vtec solenoid since the p06 isn't looking for vtec oil pressure.
|
Re: vtec on my B16
Alex look under the Rev limits tab and look where the full throttle launch section is. Make sure your rpm shift cut isnt set too low. If that stuff in enabled.
|
Re: vtec on my B16
is the vtec solenoid grounded?
|
Re: vtec on my B16
Originally Posted by crx2fast
is the vtec solenoid grounded?
|
Re: vtec on my B16
Originally Posted by CSaddict
Or plugged in? ;)
|
Re: vtec on my B16
Vtec solenoid isn't grounded through a wire, it only has the one (power) wire which I wired to my ecu. I'm throwing no codes, I have VTP disable checked, FTL is not enabled and I am just running the stockGSR bin from uber because I was just trying to test vtec, not using any crazy bins. Still the same problems as before, no vtec, 6500 RPM redline.
|
Re: vtec on my B16
u need the ground chief
start from there |
Re: vtec on my B16
Where is this ground?? There is only one wire... Wouldn't it throw a code, the stock p30 was not throwing a vtec solenoid code so I think it is wired correctly.
|
Re: vtec on my B16
there is the power wire to the solenoid and there is a wire coming back out from the clip that you ground anywhere on a clean spot on the head or wtv
|
Re: vtec on my B16
No the VTP is the one with the ground. The VTEC solenoid only has one wire.
|
Re: vtec on my B16
Originally Posted by CSaddict
No the VTP is the one with the ground. The VTEC solenoid only has one wire.
Mixed the sensors names up. |
Re: vtec on my B16
Alright well the p06 wasn't looking for a chip, hence the 6500 DX redline. I shouldve figured that out sooner :S So I soldered J1 a little bit more so then it looked for a chip, put a chip in and now solid cel limp mode. I cleaned up some solder and made sure everything was good and it still doesnt see the chip so, F it. I'm sending it to my friend J-K-tuning and having him fix it for me. Going to run the stock P30 until then, which is fine because my car just sits most weekdays so whatever. Thanks for the help guys.
|
All times are GMT -5. The time now is 04:50 AM. |
© 2024 MH Sub I, LLC dba Internet Brands