Prolly going TE! help me out..
 

Okay I am probably going to go TE as of now... the only problem is i dunno what the best burner i should buy.. someone please help me out!!! i'm pretty new to standalone, i relied on my AFC hack before and liked it a lot at 10-12 psi.. but theres nothing better than standalone... if someone would be kind enough to walk me through some stuff i still have questions about please help me.. but for now what would be the better burner to buy? please help by posting a link if you will! also this will be done on the PM6 90-91 ECU..

Re:Prolly going TE! help me out..
 

oh btw i dunno if my ECU is a 90-91... the engine is an 88 crx si engine but the body is a 91 hatch SI... but from the numbers i got from the ECU it looks like a 90?!?! how does that work...

here are the #'s on the ECU itself:

90.8.23
37820-PM6-A09
620-332738

is this a 90???

Re:Prolly going TE! help me out..
 

okay nevermind.. the A09 is burnable!!! woohoo!.. anyway, i would like to send my ECU out and get a basemap for my setup but i would like to buy a burner and tune it myself... someone help me through this!

Re:Prolly going TE! help me out..
 

the moates burn 1 from www.moates.net is handsdown the best burner for your money.

to properly tune it yourself you'll need a wideband, there are many units outhere but the best one I thought is the zeitronix one. :)

Re:Prolly going TE! help me out..
 

can the burn 1 just swap chips out without soldering them on everytime??? or is that just a kit that works universally?? also can the willem do the same? now that theres a write up on that burner fully????

Re:Prolly going TE! help me out..
 

the burner has nothing really to do with chips being swapped in and out. You chip the ecu with a socket, so you can just swap in chips whenever you want. understand?

Re:Prolly going TE! help me out..
 

yes, but TE won't let me do 390cc injectors.. thats what i have.. looks like i might have to go AFC hack again :-\

Re:Prolly going TE! help me out..
 

if someone can make me a base map for my set up i would appreciate it!! let me know and i'll tell you my set up and just send it to my email!!! BTW i'm running DSM 390cc injectors! can TE do that? i can't get it to work with anything smaller than 410cc or whatever..

Re:Prolly going TE! help me out..
 

It will do that, you just have to manually scale the values yourself. ;)

Re:Prolly going TE! help me out..
 

don't get somebody to send you a basemap. Burners aren't expensive. Just buy one and burn it yourself that way you can make adjustments whenever you want. pick up some cheap 450cc dsm injectors if you have to. I'd rather run those anyways incase you want to get a little more power.

Re:Prolly going TE! help me out..
 

i plan on blowing this engine and saving up for a B-series, so 450cc injectors are not needed...

i Have the TE program 2.1 i think and it wont' allow me to do 390cc injectors, why?

Re:Prolly going TE! help me out..
 

You select what is available and scale it manually in the map. ::)

Re:Prolly going TE! help me out..
 

alright....

Re:Prolly going TE! help me out..
 

If you are sending out your ECU to get it chipped...I'm your man. If you do send it to me it comes back to you with a basemap already on the chip.

I like the Batronix and Willem burners for the money. The Moates is a handy burner but it only accepts 3 types of chips...one of which is discontinued now and the other two most people dont know how to use correctly (from what I have seen)

As far as why you cant scale for 390s, TurboEdit doesnt let you go backwards when rescaling injectors.

http://www.-------------/te

Read my write-ups about TE and they should help you if you havent already :D

Re:Prolly going TE! help me out..
 

wheres the Export and Import options????

Re:Prolly going TE! help me out..
 

I never use them...

Re:Prolly going TE! help me out..
 

Hey xenocron! can you check out my basemap and see if i did it right??


EDIT: sent you an email! should be from draztikracing@yahoo.com

Re:Prolly going TE! help me out..
 

I wont be able to tell if you did it right or not.

Put it in the car and see how it runs!!

Re:Prolly going TE! help me out..
 

no i mean just on TE run through it and see if the #'s look right to you.. also i don't have a burner yet, i just wanted to see if i can figure this all out!

Re:Prolly going TE! help me out..
 

also can someone pull the link to the ecu chipping kit where i can just swap in and out chips?! i'll probably get the willem burner!


also from the willem page http://www.willem.org/epromshop.html

which burner should i get??

EDIT: just got this:

http://cgi.ebay.com/ws/eBayISAPI.dll...e=STRK:MEWN:IT

copying teg...

now wheres those chips?? are they one ebay too? are they 28 pin?

Re:Prolly going TE! help me out..
 

xenocron: you got money through paypal from me! chipping kit!!!

Re:Prolly going TE! help me out..
 

Im not sure what you are doing with those BINs you are emailing me...::confused::

Try re-reading the write-ups and start over. Something weird is going on.

Re:Prolly going TE! help me out..
 

ok this is messed up... i followed the instructions like 100 times already... this is pissing me off... copy and past the fuel and ignition maps into the ------ sheet, fuel maps on top from the STOCKPM6 ECU..

now in the stable maps you copy and past from the ------sheet TO the stable maps! correct? where they would normally go on the mapping, from the start.. go to properties and do 390cc injectors... okay looks fine.. go to boost options and do 115% correction... this is where it messed up and this is what i get..


Starting from 0 and on.. besides the TOP 2 calulations this is what i get starting from 0 all the way down the rpm..

0 - 7.35
.8 - 7.73
1.2 - 7.92
1.8 - 8.21
2.5 - 8.54
3.3 - 8.92
4 - 9.26
4.8 - 9.64
5.6 - 10.02
6.2 - 10.31
6.8 - 10.59
7.3 - 10.83
7.8 - 11.07
8.3 - 11.31
8.8 - 11.55
10.3 - 12.26


now the left side is what HG i believe it is and the right side is the calulations it did when i followed the instructions, now this happens to every single size injector that i do.. everyone but the top 2 are the exact same down the line! what the hell am i doing wrong!

Re:Prolly going TE! help me out..
 

No idea, try the Basemapper Deluxe program I sent you link for in my last email.

http://www.-------------/programs.htm

Re:Prolly going TE! help me out..
 

don't get the willem, get the moates burner, its so much better in everyway, its just a couple dollars more

Re:Prolly going TE! help me out..
 

Bah!

Yeah, only a couple...try double.

Willem $43 and comes with a chip

Moates $85 and comes with $$$ extra for shipping.

Re:Prolly going TE! help me out..
 

yeah i got the willem... now that theres a write up on how to get it set up it shouldn't be too hard and for 1/2 the price i'll do that little work... :)

Xenocron: did you get my paypal for that ECU chip kit???

Re:Prolly going TE! help me out..
 

Xenocron: i don't trust myself with desoldering and soldering.... just wondering if you can do that for me if i send my ecu to you and i'll give you some cash for doing it also.. let me know. i don't have that much patience with small things like that.. i'll mess that up!

Re:Prolly going TE! help me out..
 

PM'd you about hooking you up :)

Re:Prolly going TE! help me out..
 

---- I thought burners were like $300

I might have to pick one up and actually learn this program now