Engine Management eCtune , Crome , AFC , FMU , Zdyne , Hondata , EMS , TE , Uberdata Anything to control your fuel, spark needs!

Code 7 after turbo install

Old 01-29-2006, 11:42 AM
  #1  
1.0 BAR
Thread Starter
 
Join Date: Jan 2006
Posts: 251
Default Code 7 after turbo install

Well i finished installing my turbo kit last night and i cranked my car for about 30 seconds with the spark plug wires off to let the oil run throught the turbo then i fired it up and it idles anywhere for 2900-3500 rpms. I drove it down my street and its spools just fine and doesnt bog or anything. Its throwing code 7 which is throttle position sensor. well i got my volt meter and check the red wire on the plug and it was giving me like 1.637 volts with the key in the "on" position. As far as i know it should be at .5 volts right? do i have to replace it or can i adjust it? Oh and i did take the actual sensor off to put the missing link under it except i had the wrong missing link so i just put it back on with screws; could that have messed it up? Thanks the for help!
zestyskater69 is offline  
Old 01-29-2006, 11:57 AM
  #2  
3.0 BAR
 
Join Date: Jul 2003
Posts: 6,449
Default Re: Code 7 after turbo install

Sure you didnt switch the MAP and TPS plugs?
Chris Harris is offline  
Old 01-29-2006, 12:15 PM
  #3  
1.0 BAR
Thread Starter
 
Join Date: Jan 2006
Posts: 251
Default Re: Code 7 after turbo install

Hmmm, i didnt even know the plug were interchangeable, i'll give that a shot the update you guys. meanwhile, anyone else care to throw out their opinion?
zestyskater69 is offline  
Old 01-29-2006, 01:21 PM
  #4  
1.0 BAR
Thread Starter
 
Join Date: Jan 2006
Posts: 251
Default Re: Code 7 after turbo install

Well the plugs are going to the correct locations, so thats not it. On another form i was told the tps need's to be calibrated? is this correct? by the way i rollin the stock motor (d16a6).
zestyskater69 is offline  
Old 01-30-2006, 11:26 PM
  #5  
3.0 BAR
 
Join Date: Jul 2003
Posts: 6,449
Default Re: Code 7 after turbo install

If your TPS is really at 1.67 volts, its beyond fucked and couldnt be reset to spec.
Chris Harris is offline  
Old 02-01-2006, 01:50 AM
  #6  
3.0 BAR
 
Join Date: May 2004
Posts: 5,049
Default Re: Code 7 after turbo install

Originally Posted by zestyskater69
Well the plugs are going to the correct locations, so thats not it. On another form i was told the tps need's to be calibrated? is this correct? by the way i rollin the stock motor (d16a6).
Even if you think they are in the right position, try switching them. It won't hurt anything, and may fix it.
Cray91 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Slammd Sol
Forced Induction
4
03-14-2005 07:09 PM
d16tuner
Engine Management
3
04-02-2004 11:16 PM
Tilt
Forced Induction
2
01-08-2004 12:13 AM
quickcrx702
Hybrid/Tech
10
11-16-2003 12:46 AM
Chacko
Engine Management
17
04-21-2003 05:10 PM


Thread Tools
Search this Thread
Quick Reply: Code 7 after turbo install


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.