Cant get turboedit to data log?
I Have a pm6 and a data loger that I installed the other day. I also Download TurboEdit Version 2.6.1 From chris. I cant figure out how to make it work, or the order to set up the dataloger features. If some one has a step by step that thay could point out, it would help out.
|
Re: Cant get turboedit to data log?
the TE datalog is hard to get to work just search yahoo or goggle and download ecucontrol 5 or whatever the latest version is and try again
|
Re: Cant get turboedit to data log?
I disagree...the version posted on my site is the only I can get to work.
You must be using NG60 code 1st! And your drivers must installed properly and your COM ports setup accordingly... |
Re: Cant get turboedit to data log?
Originally Posted by xenocron
I disagree...the version posted on my site is the only I can get to work.
You must be using NG60 code 1st! And your drivers must installed properly and your COM ports setup accordingly... |
Re: Cant get turboedit to data log?
I tried the ng55 and I couldent get it to work, Chris said it had to be a ng60 so I burned a ng60 and I still couldnt ge tit to work. :7 I want to smash this ---- all over the street. Its so ------- frustrating!!!!!
|
Re: Cant get turboedit to data log?
Originally Posted by ratcityrex
I tried the ng55 and I couldent get it to work, Chris said it had to be a ng60 so I burned a ng60 and I still couldnt ge tit to work. :7 I want to smash this ---- all over the street. Its so ------- frustrating!!!!!
|
Re: Cant get turboedit to data log?
I tried every com port that I coud and still nothing.
|
Re: Cant get turboedit to data log?
are you getting any error messages?
|
Re: Cant get turboedit to data log?
Only when it was in the wrong port. I can get it to conect, then I press start loging and the light on the usb conector starts blinking green, but nothing shows up on my screen. If I press the active dash everthing gos all fucked up. It says that im doing 65 mph and my water is like 165* and my intake temp is 165*, but im just at idle.
|
Re: Cant get turboedit to data log?
TOOLS --> OPTIONS--> Communication
#1 - Set datalogging to the COM port assigned by your drivers (find this in the device manager, dont just try random COM ports) #2 - Set real time programming to the proper COM port or something other than your datalogging port if not using Ostrich #3 - Baud Rate 38400 APPLY AND CLOSE FILE --> DATALOGGER Connect Start Logging |
Re: Cant get turboedit to data log?
I will give that a try and let you know how it works.
|
Re: Cant get turboedit to data log?
i was getting the exact same thing, i sold it and went ODB1
|
Re: Cant get turboedit to data log?
ok here is my step by step of what im doing,
start my car pulg in my usb to com 6, thats where my driver loaded open turbo edit goto file, open, my ng60 bin Go to tools, options, comunications, set dataloging to com6, set rtp to com 1, baud rate to 38400 apply and close then I go to File, Dataloging click conect, start loging. thats where it ends. nothing happens on my screen, but the green light on my cable bilnks green. WTF? :7 |
Re: Cant get turboedit to data log?
im guessing you are using the TE plugin? do you have your wideband settings right? sample rate?
also, is your datalogging cable soldered to the board? or is it removable? i had a similar issue with my serial cable, turns out that i had it plugged into the board backwards... |
Re: Cant get turboedit to data log?
well i tried everygthing, so this morning I thought ---- it I will pull my pm6 out and put the data loging conection on to my pr4. So I flip ovet the pm6 pull the screws out and low and behold what do I see? A ------- microscopic chunk of solder sitting between 2 pins on the header. So I scraped my finger across it and it fell out from between the two. Im ------- so pissed of that I didnt check to see if it was that first. Just a :1 mistake. So now I get a runtime error with te,I can log now with ecu control but still no te?
|
Re: Cant get turboedit to data log?
Hrm...runtime error, that I am clueless on. I wish TE was still being developed :(
|
Re: Cant get turboedit to data log?
Well I uninstalled te and reloaded it and wala!!!!! ------- bad ass, now I just need to run my plx to my ecu so I can datalog my wideband info . Thanks for the help Chris, to bad Im a ------- noob and Was ready to give up. But it payed off sticking to it. ;D
|
Re: Cant get turboedit to data log?
Glad you got it working 8)
|
Re: Cant get turboedit to data log?
Originally Posted by xenocron
Hrm...runtime error, that I am clueless on. I wish TE was still being developed :(
|
Re: Cant get turboedit to data log?
Can someone tell me why you must use the NG60 code. Im using the NG55 and its working
|
Re: Cant get turboedit to data log?
If you are using NG60 use BRE, it supports PM6/PR4 AND it datalogs... Maptrace... Autotune... Obd0... it works!
It will read TE's NG60 maps too btw. |
All times are GMT -5. The time now is 04:26 AM. |
© 2024 MH Sub I, LLC dba Internet Brands