i need a motor bitches.......and some other stuffs
#1
i need a motor bitches.......and some other stuffs
i dont have any money so you have to trade and i am not going to ship anything i have because i am lazy.
i have theses things:
1992 LS engine and trans/axles, 5k on dizzy, 12k on t-belt, water pump, clutch(exedy), flywheel (10#), plugs, and wires. no ex mani or wiring included. - $850
EF b-series cable mounts, 12k on them - $150
EF b-series linkage w/ b&m short shifter - $130
2.25" magna flow cat, 6k mi, direct bolt in for b-series into EF so you dont need to cut up your exhaust(may fit others, i'm not sure) - $120
el cheapo 4-2-1 2 piece header - $100
1991 PR4 ecu - $70
60mm stainless exhaust, 88-91 hatch. non rice, painted grey and tip cut off - $175
CRX Si front sway bar, no endlinks - $35
new LS timing belt - $30
EF poly trailing arm bushings - $20
i have a blown holset h1c(early dodge cummins turbo,HUGE) if anyone is interested, i cant remember where i put it but if someone is interesed i'll see if i can find it
any interior parts, except dash, door panels, and front seats. bluishgrey color, most are in great shape. just ask i prob have it, rear seats are vinyl.
most of my susp will be for sale once i figure out what is causing the vibration, dont wanna sell any bunk parts.
i want these things......
d16a6 or DOHC ZC complete swap,engine can be blown just no bent rods, scarred crank, or major ****.(eng, trans, axles, linkage w/shifter, mounts, dizzy, int mani/tb, all sensors)
EF traction bars
non-ebay BOV
450-650cc inj (sat or non-sat doesnt matter)
3" 88-91 hatch exhaust
d-series t3 mani (ext or int gate doesnt matter)
2.5" FMIC piping
94-newer b-series TB
LM-1 or LC-1 WBo2 setup
honda/T3 oil lines
i am located in your mom's dirty ----- (aka Washinton DC)
i have theses things:
1992 LS engine and trans/axles, 5k on dizzy, 12k on t-belt, water pump, clutch(exedy), flywheel (10#), plugs, and wires. no ex mani or wiring included. - $850
EF b-series cable mounts, 12k on them - $150
EF b-series linkage w/ b&m short shifter - $130
2.25" magna flow cat, 6k mi, direct bolt in for b-series into EF so you dont need to cut up your exhaust(may fit others, i'm not sure) - $120
el cheapo 4-2-1 2 piece header - $100
1991 PR4 ecu - $70
60mm stainless exhaust, 88-91 hatch. non rice, painted grey and tip cut off - $175
CRX Si front sway bar, no endlinks - $35
new LS timing belt - $30
EF poly trailing arm bushings - $20
i have a blown holset h1c(early dodge cummins turbo,HUGE) if anyone is interested, i cant remember where i put it but if someone is interesed i'll see if i can find it
any interior parts, except dash, door panels, and front seats. bluishgrey color, most are in great shape. just ask i prob have it, rear seats are vinyl.
most of my susp will be for sale once i figure out what is causing the vibration, dont wanna sell any bunk parts.
i want these things......
d16a6 or DOHC ZC complete swap,engine can be blown just no bent rods, scarred crank, or major ****.(eng, trans, axles, linkage w/shifter, mounts, dizzy, int mani/tb, all sensors)
EF traction bars
non-ebay BOV
450-650cc inj (sat or non-sat doesnt matter)
3" 88-91 hatch exhaust
d-series t3 mani (ext or int gate doesnt matter)
2.5" FMIC piping
94-newer b-series TB
LM-1 or LC-1 WBo2 setup
honda/T3 oil lines
i am located in your mom's dirty ----- (aka Washinton DC)
#2
Re: i need a motor bitches
you suck at life.....jk
I'm not a member and I'm not going to sign up but give me a list of what you have to trade i might be able to find you an a6, I'm SE PA
The following errors were found:
The board administrator requires all members to log in
The board administrator requires all members to log in
#5
Re: i need a motor bitches.......and some other stuffs
i have a a6 swap(just motor,tranny with absolutly no grinds, perfect shape,linkage,dizzy,mounts,aftermarket intake mani,tb, and ill throw in my polished a6 crank, a like new oil pump with under 1000 miles on it, and an already tapped oil pan mint condition) basically everything except for axles and sensors, jus cuz i need the sensors for my ls swap...um i can trade you this for ur 60mm exhaust, the new timing belt,the sway bar,and if u want to give me that water pump and exedy clutch from ur swap there... lmk asap, cuz i am looking for exhaust to fit my ef for my ls swap
o btw, the motor is shot but all it needs is a new head and new set of rings and it will be good to go
and also, y is it 60mm? isnt that like 2 1/3" exhaust?? lol seems like an odd measurement
o btw, the motor is shot but all it needs is a new head and new set of rings and it will be good to go
and also, y is it 60mm? isnt that like 2 1/3" exhaust?? lol seems like an odd measurement
#9
Re: i need a motor bitches.......and some other stuffs
Originally Posted by Racintweek
i have a blown holset h1c(early dodge cummins turbo,HUGE) if anyone is interested, i cant remember where i put it but if someone is interesed i'll see if i can find it
Thanks