FS: GA. BUILT ZC D16 Full swap
#1
FS: GA. BUILT ZC D16 Full swap
Okay guys school is starting soon and i have to pay tuition. So I decided to sell my built ZC engine with trans. This engine has literally less than 5 miles on it. After I built it and installed it into my civic, I took it around the block a couple times. This engine should support up to 400hp and even more If you have the supporting mods(injectors/turbo setup). I've seen guys with similar, yet the same setup make 460hp on stock sleeves.
This engine and trans is being pulled out as we speak. Be ready for a new thread for the part out!
If there is no interest in buying the whole engine/trans swap, then i will de-assemble the engine and part it out.
Specs:
JDM ZC engine (same as a D16A6, but JDM Spec)
Vitara Pistons ( est. c/r is 7.5 c/r)
-with new piston rings
Tuner Toys Billet rods with ARP 2000 Rods bolts
KMS Block Guard
Cometic 3 layer metal head gasket
ACL RACE crank and rod bearings
Ported and Polished Head
JG Engine Dynamics Valve Springs and titanium retainers
ALL NEW seals, gaskets throughout the whole engine
ARP Head Studs
GSR Throttle Body
DSM 450cc Injectors
Findanza 9 Pound flywheel
XTD Stage 3 clutch pressure plate (needs to be broken in)
JDM S20 trans (no grinds)
I do have the shift linkages and EF Polyurethane filled mounts to go with it.
NOTE: the Hasport hydraulic to cable conversion can go with it for a extra 200 dollars firm.
PRICE:
$2000 obo
CONTACT METHOD:
PM ME, or PM ME for a phone number
Thanks for looking!
beginning to the end
tuner toys rods compared to the stock rods( the new vitara pistons installed)
Engine assembled
Head after the ported/clean up (half of the new valve springs were installed)
Engine installed (only pictures i have of the engine after i assembled it)
A picture shortly after took the engine out
This engine and trans is being pulled out as we speak. Be ready for a new thread for the part out!
If there is no interest in buying the whole engine/trans swap, then i will de-assemble the engine and part it out.
Specs:
JDM ZC engine (same as a D16A6, but JDM Spec)
Vitara Pistons ( est. c/r is 7.5 c/r)
-with new piston rings
Tuner Toys Billet rods with ARP 2000 Rods bolts
KMS Block Guard
Cometic 3 layer metal head gasket
ACL RACE crank and rod bearings
Ported and Polished Head
JG Engine Dynamics Valve Springs and titanium retainers
ALL NEW seals, gaskets throughout the whole engine
ARP Head Studs
GSR Throttle Body
DSM 450cc Injectors
Findanza 9 Pound flywheel
XTD Stage 3 clutch pressure plate (needs to be broken in)
JDM S20 trans (no grinds)
I do have the shift linkages and EF Polyurethane filled mounts to go with it.
NOTE: the Hasport hydraulic to cable conversion can go with it for a extra 200 dollars firm.
PRICE:
$2000 obo
CONTACT METHOD:
PM ME, or PM ME for a phone number
Thanks for looking!
beginning to the end
tuner toys rods compared to the stock rods( the new vitara pistons installed)
Engine assembled
Head after the ported/clean up (half of the new valve springs were installed)
Engine installed (only pictures i have of the engine after i assembled it)
A picture shortly after took the engine out
#5
Re: FS: GA. BUILT ZC D16 Full swap
Well since the engine was started up and driven down the street and removed the engine out, i believed the price was fair with the engine having < 3 miles. Since i bought all the parts new and it's well even for my asking price. And the price was for the full swap.
The short block is sold.
Thanks for your concern!
The short block is sold.
Thanks for your concern!
Thread
Thread Starter
Forum
Replies
Last Post
sleeplsm
Turbo Parts For Sale
47
03-13-2007 06:54 PM
Smooth_Imports
Turbo Parts For Sale
3
07-07-2006 03:01 PM
Instigator_CRX87
Turbo Parts For Sale
18
08-22-2005 11:41 AM
ssl2k
Turbo Parts For Sale
29
11-28-2004 11:36 PM