FS/feeler: 4g civic/d-series parts
#1
FS/feeler: 4g civic/d-series parts
Some of the stuff I have got back, some I have not, and I'm still deciding if I should buy another civic to swap my parts to or move on to a new project right now.
Avid racing traction bars-0 miles-$200
Ksport coilovers-0 miles-$500
Si trans/dx final drive/OBX LSD (includes Si final, but the dx is installed)-0 miles-$500
91 hatch DX Rolling chassis w/ ES bushing full kit (0 miles), clean title, Si-R front spindles/brakes (trans mount hacked off by thief, very little rust)~140k-$800
bone stock D15B2, 120k-$50
fidanza 7.5, clutch specialties 6puck unsprung, 0 miles-$300
Si rear sway bar w/ brackets-$50
upper strut bars, 2 sets-$20/set
lower strut bars-$20/set
c pillar bar-$20
90-91 gauge cluster w/ white face (El-glo on numbers ONLY)-$75
PM6 ecu's (3 available)-$50/each
OBX intake mani hacked for ITB's (includes yami R1 carbs that need work)-$150
OBX cat-back exhaust, limited use, $150
ebay 'cat'-$20
OBX header, rusty but functional-$20
Y8 intake manifold-$50
EG civic lower front H-brace-$25
Avid racing traction bars-0 miles-$200
Ksport coilovers-0 miles-$500
Si trans/dx final drive/OBX LSD (includes Si final, but the dx is installed)-0 miles-$500
91 hatch DX Rolling chassis w/ ES bushing full kit (0 miles), clean title, Si-R front spindles/brakes (trans mount hacked off by thief, very little rust)~140k-$800
bone stock D15B2, 120k-$50
fidanza 7.5, clutch specialties 6puck unsprung, 0 miles-$300
Si rear sway bar w/ brackets-$50
upper strut bars, 2 sets-$20/set
lower strut bars-$20/set
c pillar bar-$20
90-91 gauge cluster w/ white face (El-glo on numbers ONLY)-$75
PM6 ecu's (3 available)-$50/each
OBX intake mani hacked for ITB's (includes yami R1 carbs that need work)-$150
OBX cat-back exhaust, limited use, $150
ebay 'cat'-$20
OBX header, rusty but functional-$20
Y8 intake manifold-$50
EG civic lower front H-brace-$25
#8
Re: FS/feeler: 4g civic/d-series parts
bump
finally got the legal details figured out, and i hit a deer with my DD. Everything is available. Low ballers welcome, local pickup preferred cause now my transportation is sketchy. PM, reply, or call 319-329-4680.
finally got the legal details figured out, and i hit a deer with my DD. Everything is available. Low ballers welcome, local pickup preferred cause now my transportation is sketchy. PM, reply, or call 319-329-4680.
#9
Re: FS/feeler: 4g civic/d-series parts
I gotta figure out what tranny I have in my car before I decide, but I need a new clutch. Im assuming since you have a 90-91 tranny, that the flywheel is 212mm, and the clutch is 20 spline, right What torque and clamping force is the pressure plate and clutch rated at?
Thread
Thread Starter
Forum
Replies
Last Post
turbotercel
Forced Induction
1
06-01-2015 11:58 PM
SpeedyJAY
Wanted
3
04-27-2007 05:03 PM