dohc ZC / srt-4 ARP headstuds.
08-30-2007, 10:41 PM
#1
1.5 BAR
Thread Starter
Join Date: Mar 2004
Posts: 688
dohc ZC / srt-4 ARP headstuds.
The headstuds and pan are sold. I do still have from the dohc zc.
Stock cams
Stock head minus rockers
Timing belt cover
Almost brand new honda A6 oil pump.
Make an offer on any of it
Check out my feedback on ebay under the same name as here, daubleaaron.
Paypal is: underpressure91@yahoo.com
Stock cams
Stock head minus rockers
Timing belt cover
Almost brand new honda A6 oil pump.
Make an offer on any of it
Check out my feedback on ebay under the same name as here, daubleaaron.
Paypal is: underpressure91@yahoo.com
08-31-2007, 04:47 PM
#4
1.5 BAR
Thread Starter
Join Date: Mar 2004
Posts: 688
Re: dohc ZC / srt-4 ARP headstuds.
hardcore gang? Its been a while since I've seen any hardcore rides come from the TC hmt gang 
And I dont go to mnsc meets. the only meets I go to are the TC HMT meets. And well there has not been one this summer. Why is that? Mr hmt president with a garage and a grill? Call a ------- meet, grab a camera and Ill show you some dirty seconds 
But meanwhile someone buy my zc ----..
And I dont go to mnsc meets. the only meets I go to are the TC HMT meets. And well there has not been one this summer. Why is that? Mr hmt president with a garage and a grill? Call a ------- meet, grab a camera and Ill show you some dirty seconds But meanwhile someone buy my zc ----..
09-01-2007, 04:31 PM
#7
1.5 BAR
Thread Starter
Join Date: Mar 2004
Posts: 688
Re: dohc ZC / srt-4 ARP headstuds.
how about $20 for the pan. If you buy the studs Ill throw the pan in for $10 
As for the condition of the studs. They are ------- mint. and I put as many miles on the car as I could in one summer with these studs. The car dyno'd at like 12 psi with a .48/.60 and made 208 hp on a mustang dyno. I then put a .63 turbine housing on and cranked the boost up to 20 psi which should have made around 300. I never blew a headgasket and they were torqued to 65ft lbs just like arp says to do with there moly lube. Ill put pics up even though everyone knows what these look like.
As for the condition of the studs. They are ------- mint. and I put as many miles on the car as I could in one summer with these studs. The car dyno'd at like 12 psi with a .48/.60 and made 208 hp on a mustang dyno. I then put a .63 turbine housing on and cranked the boost up to 20 psi which should have made around 300. I never blew a headgasket and they were torqued to 65ft lbs just like arp says to do with there moly lube. Ill put pics up even though everyone knows what these look like.
09-01-2007, 11:56 PM
#8
1.0 BAR
Join Date: Dec 2005
Location: clovis nm, crapville
Posts: 312
Re: dohc ZC / srt-4 ARP headstuds.
yea i know what they look like. just a little cautious in possible buying used studs, what happened to the engine, why did you stip it down. so 10 extra for the pan with the studs, so like 65 shipped then.
09-02-2007, 12:34 AM
#9
1.5 BAR
Thread Starter
Join Date: Mar 2004
Posts: 688
Re: dohc ZC / srt-4 ARP headstuds.
The engine got stripped down because it turns out im not much of a tuner. After a summer of boosting on it I burnt the top of two pistons. I didnt want to buy new pistons for it so I went b-series
