ZC trans on a D16Z6 in an EF.. what axles?
 

I was under the impression that the dohc ZC trans was the same as any other us d-series trans, I was wrong. My axles from my EF don't fit at all :-/

What are my options here? I know I can use an integra passenger side axle but the drivers side? The d16z6 doesn't have the bolt holes for the half shaft, well it does but they're not drilled or tapped so using a half shaft is kinda out of the question.


So basically my question is, are there any axles I can use that will drop right in without having to change inner joints or making a half shaft work?

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

Since there arent any replies im going to take a wild guess and say, ZC axles??

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

zc halfshaft


zc axles

or 90-93 teg axles with inner hub thingy removed that how I ran mine



thread your block with the right thread pattern for halfshaft


halfshaft bolts are a special kind and the only kind used in a car dont try a normal bolt unless you want major headaches


the bolts are a taper style


good luck

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

Could you nab the axles and half shaft off of a 1g integra?

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

noppers


totaly different


you could rig the half shaft only 2 bolts will line up


the axles are totally wrong spline

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

the problem is I dont have the zc half shaft; It was left in denver when I moved back. I can get it but it'll be a while.

I may try to snag a set of da axles and take the inner joints off and put them on my EF axles; or at least the drivers side and use a passenger side DA axle.

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

simple rule you need that zc shaft no other way around it

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

did you not read what i typed.

i'll just take the inner joint off a passenger side da axle and put it on the long civic cv shaft.... make a totally custom jdm axle y0

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

Probably gonna piss oil all over the place until the transmission case is empty. IDK though. I would imagine that the oil seal is different on that side. I know it is on a B series transmission.

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

WONT WORK...

you all are forgetting something VERY important.... there is no way to mount the ZC intermediate shaft that he doest have [and probably wont be able to find], there are no threaded holes in the back of a D16Z6 to bolt the shaft to... just ZC;s and D16A6's... D16A6 was also in a Wagovan, they had intermediate shafts, and i have a bet that would work for this application....

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

i ran the 89 teg shafyt with it hack up to ----. it worked temporarily but it didnt seal right. You can ue that temporarily till you get the right one. I would go through honda-tech to source one. I found atleast 3 guys that had thema nd i got mine fro like 50 bux. The part about the wholes ont he back of the block is true. YOu need the original thread pitch otherwise it will just strip with too much torque. I say find out the pitch thread and get the right tap. i imagine you can use the bolts that come on the intregra ( the 89 teggy) .

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

all intermediate shaft bolts are the same: 90102-SF1-000

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

you need the ZC intermeidate shaft. and 89 teg axels are the best fit. I tried 91's and they both broke maybe because they were 91 or they were just crappy rebuilds from olympic but hey 89 teg axels + zc intermediate shaft.

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

the inner joint is a different length for the driver side, it WILL not lock in.

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

The holes are there on most Z6's, just need tapped. Not hard.

EASY cure.

Install a OBX with new axle seals and run normal axles. Drop in a 4.25 FD and .771 5th gear while inside.

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

or do what bone said


I have had a zc trans on my old d set up and have a couple friends with jdm d15b's with them that got creatitive with making brackets to mount the shaft and both are working great both boosted with no problems. zc shaft/90-93 teg axles has been the answer for years follow what works

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

I'd love to see those mounts, just 1/8" plate????

PM pics if need to keep under wraps.

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

bone pm amkrew on here

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

his GF giving BJ's?

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

call noyan usa. when I needed one they had a few laying around. www.noyanusa.com

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

I have a ZC intermediate shaft from a buddys car that I have laying around in my garage from a ZC trans that fucked up on him PM me and we can work something out!

Re: ZC trans on a D16Z6 in an EF.. what axles?
 

no he is the one running it he might take a pic for ya