My whole goddamn swap has gone to ----!!!
07-10-2007, 05:17 PM
#1
1.5 BAR
Thread Starter
Join Date: Jan 2006
Posts: 1,157
My whole goddamn swap has gone to ----!!!
90' CRX DX, attempted B18a1
Here's problem #1.. old Axle inboard joints are ------- TIIIGHT on the intermediate shaft.. Can't get them off for ----.. pryed and pryed and pryed. any advice?? i've tried everything and the whole goddamn intermediate shaft moves when I pry like a bad bitch.
Here's Problem #2.. Header I bought is a 1 piece 4-1 header.. and it wont go in there unless I remove the front cross member .. yay
Problem #3.. Had a company (monotech) make me a harness.. there isn't a plug for my 02 sensor, just 2 little wire nubs that look like Radiator plug ins. It's a 1 wire 02
Problem #4.. I'm out of Corona
Here's problem #1.. old Axle inboard joints are ------- TIIIGHT on the intermediate shaft.. Can't get them off for ----.. pryed and pryed and pryed. any advice?? i've tried everything and the whole goddamn intermediate shaft moves when I pry like a bad bitch.
Here's Problem #2.. Header I bought is a 1 piece 4-1 header.. and it wont go in there unless I remove the front cross member .. yay
Problem #3.. Had a company (monotech) make me a harness.. there isn't a plug for my 02 sensor, just 2 little wire nubs that look like Radiator plug ins. It's a 1 wire 02
Problem #4.. I'm out of Corona
07-10-2007, 05:41 PM
#6
3.0 BAR
Join Date: Apr 2006
Posts: 3,015
Re: My whole goddamn swap has gone to ----!!!
well first of all 4-1 headers were not designed to go in the EF chassis.. 4-2-1 header FTW.. secondly hit the axel with the BFH and pry at the same time it will pop right out.. third go to the store and get more beer. and last thats what you get when you have someone make ---- for you
07-10-2007, 05:45 PM
#7
1.5 BAR
Join Date: Sep 2006
Posts: 1,171
Re: My whole goddamn swap has gone to ----!!!
#1: old *** axles, get some new ones
#2: cutting torch and welder
#3: make your own gaddam harness, dont rely on someone else's ching chong meow ----, or run your wires yourself
#4: pabts blue ribbon, beer ***** FTL....
dont ever buy someone else's fucked up swap....i flame you for that.
#2: cutting torch and welder
#3: make your own gaddam harness, dont rely on someone else's ching chong meow ----, or run your wires yourself
#4: pabts blue ribbon, beer ***** FTL....
dont ever buy someone else's fucked up swap....i flame you for that.
07-10-2007, 05:48 PM
#8
1.5 BAR
Thread Starter
Join Date: Jan 2006
Posts: 1,157
Re: My whole goddamn swap has gone to ----!!!
Originally Posted by jagojon3
Just put the tools down and step away from the car.... forever.
This is not a joke.
This is not a joke.
07-10-2007, 06:17 PM
#9
1.5 BAR
Thread Starter
Join Date: Jan 2006
Posts: 1,157
Re: My whole goddamn swap has gone to ----!!!
yay i got them out.. now the new goddamn axles wont go in because of that ------- pin.. and i dont have the right goddamn tools,a nd i'm using a sledge just fuckign up my new axles.. yay.. i'm real close to putting a bullet in my .30 .30 and ending my life
