maybe u guys can help?? (f*ck HT and ZCR they suck)
 

well ive tried posting in all the other forums and since you guys arent dumbasses i figured id see if u all could help me. DOHC ZC and well like so many other people i have a problem with bogging out at WOT. it accelerates fine if i ease into it but if im rolling in second at around 3k and floor it the engine bogs out for a good 3-4 seconds before it can catch up. IVE TRIED ALOT TO TRY AND STOP THIS!!!!!! it has new plugs, wires, dizzy, rotor, cap, coil, new fuel filter, new pump. the compression is good,the tps is reading .52@closed and 4.56@ WOT, and the timing is set to stock. ive had this engine for a year and as of today all the parts and settings listed above have not cured the bogging. plz help me out im just frustrated and running out of money.

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

anybody??

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

What ECU are you running?

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

pm6

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

Try a PG7.

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

Every ZC I have every seen has had wierd issues with idle and ----, or has run gansta rich. Good luck with finding your problem, we've tried everything, check the map sensor next.

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

Also try a Pr4 ECu.

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

Nobody's going to recommend the correct ECU for the car?

What other forums? Hybrid/Tech or Engine Management? I don't see any posts there... :8

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

isnt the right ecu a pg7? eventhough this should be in the "tech" section

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

no not other sections on here, other sites. what are the pg7 and pr4 out of???

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

PG7 = D16A1, (OBD0) PR4 = B18A1. Neither are ZC part numbers.

The ZCR, while you don't think much of the diagnostic skills of the members, has basic ZC information that you are too lazy to read. Until you become unlazy and read it, we have to waste our diagnostic skills trying to overcome your generally high level of ignorance. You cannot polish a turd, you cannot teach a pig to fly, we cannot out think what you don't know or don't know is important.

Spend ten minutes reading basic ZC FAQ and then make a post in the correct forum. I will assist you there.

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

hmm i thought it was pg7......i forgot it's pm7 (it was stamped all over my dohc zc internals, when they were stock)

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

its a pm7 I sold one a few months ago, it came out of a German spec crx with a d16a9 motor

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

well actually ive read everything on this subject on both sites and if u read the posts they are just asking me questions which ive already answered. for instance: i said in my first post that i dont have any cels and if you read down maybe 5 or 6 people posted " do u have any cels??" and ur telling me read?? its seems like its always flame first ask second EVERYWHERE. forget i even asked u guys

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

Ok, buh bye.

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

I did none of those things, I told you what to do, I told you I would answer your questions if you manned up and met me halfway.

You aren't serious about fixing your car, boy. Just buy a Cavalier and put a set of rims on it, and call it a day, huh?

Re: maybe u guys can help?? (f*ck HT and ZCR they suck)
 

alright later