Link to H-T for Bearings?
#1
Link to H-T for Bearings?
I looked for it but could source it:
Does anyone have the link to Honda-Tech for the Colour to thickness measurements of honda OEM bearings. Particularly D-Series bottem ends?
I saw it a while back but now can't find it. I knew I should have book marked it!
Does anyone have the link to Honda-Tech for the Colour to thickness measurements of honda OEM bearings. Particularly D-Series bottem ends?
I saw it a while back but now can't find it. I knew I should have book marked it!
#2
Re: Link to H-T for Bearings?
Okay found this, but are D and B colours the same thickness?
Main Bearing thickness by color
Blue 2.013-2.010 mm 0.0793”- 0.0791”
Black 2.010-2.007 mm 0.0791”- 0.0790”
Brown 2.007-2.004 mm 0.0790”- 0.0789”
Green 2.004-2.001 mm 0.0789”- 0.0788”
Yellow 2.001-1.998 mm 0.0788”- 0.0787”
Pink 1.998-1.995 mm 0.0787”- 0.0785”
Red 1.995-1.992 mm 0.0785”- 0.0783”
Rod bearing thickness by color
Blue 1.510-1.507 mm 0.0594”- 0.0593”
Black 1.507-1.504 mm 0.0593”- 0.0592”
Brown 1.504-1.501 mm 0.0592”- 0.0591”
Green 1.501-1.498 mm 0.0591”- 0.0590”
Yellow 1.498-1.495 mm 0.0590”- 0.0589”
Pink 1.495-1.492 mm 0.0589”- 0.0587”
Red 1.492-1.489 mm 0.0587”- 0.0586”
Main Bearing thickness by color
Blue 2.013-2.010 mm 0.0793”- 0.0791”
Black 2.010-2.007 mm 0.0791”- 0.0790”
Brown 2.007-2.004 mm 0.0790”- 0.0789”
Green 2.004-2.001 mm 0.0789”- 0.0788”
Yellow 2.001-1.998 mm 0.0788”- 0.0787”
Pink 1.998-1.995 mm 0.0787”- 0.0785”
Red 1.995-1.992 mm 0.0785”- 0.0783”
Rod bearing thickness by color
Blue 1.510-1.507 mm 0.0594”- 0.0593”
Black 1.507-1.504 mm 0.0593”- 0.0592”
Brown 1.504-1.501 mm 0.0592”- 0.0591”
Green 1.501-1.498 mm 0.0591”- 0.0590”
Yellow 1.498-1.495 mm 0.0590”- 0.0589”
Pink 1.495-1.492 mm 0.0589”- 0.0587”
Red 1.492-1.489 mm 0.0587”- 0.0586”
#3
Re: Link to H-T for Bearings?
i would assume so. im going to honda sometime this week for some bearings. probably just going to buy 2 brown bearings because their cheap just to spec out which ones i need. the greens are like 12 bucks a piece maybe i should just ask one of those guys there. i doubt they'd know though
#4
Re: Link to H-T for Bearings?
There are markings on your block and crank that tell you what size you need. If the crank has been polished, yeah, it gets a little off sometimes. Otherwise, you are good to go.
Why not run a $50 set of ACLs and be done with it?
Why not run a $50 set of ACLs and be done with it?
#5
Re: Link to H-T for Bearings?
Do the ACL bearings have all the diffrent thicknesses that the honda bearings do? I am building a gsr that the crank just was turned .10 and it had green honda bearings in it before. I am going to run ACL's. So do i just get .10 over bearings?
steve
steve
#7
Re: Link to H-T for Bearings?
Originally Posted by Joseph Davis
There are markings on your block and crank that tell you what size you need. If the crank has been polished, yeah, it gets a little off sometimes. Otherwise, you are good to go.
Why not run a $50 set of ACLs and be done with it?
Why not run a $50 set of ACLs and be done with it?
Thread
Thread Starter
Forum
Replies
Last Post
89civichatch89
Wanted
8
04-14-2008 01:27 AM
LSD Motorsports
Turbo Parts For Sale
17
05-16-2007 07:35 PM