I'm thinking about getting cams reground.
Well, as most know I have a stock B18A1 and plan to keep it a B18A1, I dont want to spend a fortune on cams but I would like to rev up to 8K and make some power, basically its come down to this, you dont need big PSI or CFM to take the lead, I plan to boost this engine using my Garret T3, its a good size turbo for a 1.8 liter engine, I plan to take boost (8 psi) up to 8K not further since I risk spinning a bearing at thoes RPM's and anything over 8K would require aftermarket internals in the head.
What are some options here? I know I wont have to replace the springs and ---- since its only 500 RPM or so more than stock fuel cut off. Let me know, The way I see it is 8 psi, up to 8k shift point on a 1.8 liter Turbo Motor with no CAT and in a light CX 4 door, this car should run some nice times at the track. hoping for low 13's, high 12's @ 11 meters below Sea level, since I know a guy that has a B16A2 in a stripped Si EG hatch that runs 13.8 at the track we go to, and thats on street tires too. Another guy with 8 psi and a D16Z6 ran mid 13's, same type of hatch, so I dont see why I wouldnt be able to get high 12's on slicks. |
Re: I'm thinking about getting cams reground.
you should run high 12's without even opening the motor...........
B18B1 with Greedy D series made to fit, 22x8x15 slicks that didn't hook, 12.91 @ 108 mph....... |
Re: I'm thinking about getting cams reground.
DElta is really the only company that is less than a 100 per cam. If you go w/ a mild grind stock springs are fine
|
Re: I'm thinking about getting cams reground.
Originally Posted by chris
DElta is really the only company that is less than a 100 per cam. If you go w/ a mild grind stock springs are fine
|
Re: I'm thinking about getting cams reground.
Is there shops what can grind stock cams? or do I have to go with aftermarket?
|
Re: I'm thinking about getting cams reground.
Yeah there's delta, and I think Web does it too. Pretty cheap compared to aftermarkter cams like Crower and Skunk2. Where you'd put down your lifesavings to get a set of nice cams.
|
Re: I'm thinking about getting cams reground.
delta grinds stockers for 85 a piece
|
Re: I'm thinking about getting cams reground.
Originally Posted by chris
delta grinds stockers for 85 a piece
|
Re: I'm thinking about getting cams reground.
No way the equipment used is freakin crazy and expensive. Any other cam grinder is 200+ per cam
|
Re: I'm thinking about getting cams reground.
your not gonna make power to 8k without a cam larger than you can get out of a regrind. id look to crower turbo cams they have 270/235 degrees duration intake/exhaust and .469" lift. you will need new springs though for anything higher than stock redline, stock LS springs suck. also if its a b18a going to a b18b or b20 head/intake setup would be worth your time and effort. intake ports are bigger (about 2mm wider) and the inatke manifold and TB are bigger too.
|
Re: I'm thinking about getting cams reground.
Originally Posted by Xgenturbo
Originally Posted by chris
delta grinds stockers for 85 a piece
http://www.coltcams.com/ http://www.shadboltcams.com/ |
Re: I'm thinking about getting cams reground.
what are there costs on the grinds colt and http://www.shadboltcams.com/
|
Re: I'm thinking about getting cams reground.
Originally Posted by Jcushing
your not gonna make power to 8k without a cam larger than you can get out of a regrind. id look to crower turbo cams they have 270/235 degrees duration intake/exhaust and .469" lift. you will need new springs though for anything higher than stock redline, stock LS springs suck. also if its a b18a going to a b18b or b20 head/intake setup would be worth your time and effort. intake ports are bigger (about 2mm wider) and the inatke manifold and TB are bigger too.
Just stick w/ stock redline martin. |
Re: I'm thinking about getting cams reground.
you should have upgraded you engine while it was on the engine stand
Its more work than you think if you wanna start reving higher and get a decent amount of power |
All times are GMT -5. The time now is 10:59 PM. |
© 2024 MH Sub I, LLC dba Internet Brands