Help me design my build.
I need to start putting together a projext car, I hope to have it together by next summer, which isn't bad considering I don't have the car or any parts yet. :)
Plans: 92-95 civic hatch D16Z6 or D16Y8 Tuner toys rods weisco pistons comp cams stage 2 cam crower springs and retainers stainless valves (haven't decided on a brand yet) Haven't decided on a clutch/flywheel set yet. I want this to be a low 11 sec/ high 10 sec car by the time the project is complete. I can't decide on which turbo to run on this car, I want to run in the 25-30 psi range but still spool before the rev limit, a t3 .60/.63 wouldn't be big enough to efficiently push that much boost is it? I'll probably run a KRBfab (i think that is their name) mani/3 inch downpipe. 3 inch charge pipes, Greddy type RS BOV, and a tial 38 mm WG with an open dump tube. Tuning of course with Crome pro. :) Last, will be a Zex bottle to give me the little push into my goal 1/4 mile time. :) Anyone see any flaws in this list so far? I'm assuming this will be too much for a JRC or CCA IC, so are there any other HMT approved brands? Will that turbo hold up? If not, what should I run? Any ideas on a clutch/flywheel brand? Any ideas on a valve brand? Any other suggestions on this list are greatly appreciated. |
Re: Help me design my build.
Dont want to burst your bubble but there have been like 3-4 low 11 sec/10 sec d series and those mods are good for maybe high 200's. To run low 11's you need 10g's+ its reality
|
Re: Help me design my build.
Originally Posted by Darkelvis
I need to start putting together a projext car, I hope to have it together by next summer, which isn't bad considering I don't have the car or any parts yet. :)
Plans: 92-95 civic hatch D16Z6 or D16Y8 Tuner toys rods weisco pistons comp cams stage 2 cam crower springs and retainers stainless valves (haven't decided on a brand yet) Haven't decided on a clutch/flywheel set yet. I want this to be a low 11 sec/ high 10 sec car by the time the project is complete. I can't decide on which turbo to run on this car, I want to run in the 25-30 psi range but still spool before the rev limit, a t3 .60/.63 wouldn't be big enough to efficiently push that much boost is it? I'll probably run a KRBfab (i think that is their name) mani/3 inch downpipe. 3 inch charge pipes, Greddy type RS BOV, and a tial 38 mm WG with an open dump tube. Tuning of course with Crome pro. :) Last, will be a Zex bottle to give me the little push into my goal 1/4 mile time. :) Anyone see any flaws in this list so far? I'm assuming this will be too much for a JRC or CCA IC, so are there any other HMT approved brands? Will that turbo hold up? If not, what should I run? Any ideas on a clutch/flywheel brand? Any ideas on a valve brand? Any other suggestions on this list are greatly appreciated. try a sc61 ballbearing turbo your on your own for a IC *might* have a problem pushing enough cfm's to push 30lbs. through a full 3in diameter charge pipe before you hit your revlimiter. its only 1.6 liters... |
Re: Help me design my build.
Originally Posted by chris
Dont want to burst your bubble but there have been like 3-4 low 11 sec/10 sec d series and those mods are good for maybe high 200's. To run low 11's you need 10g's+ its reality
the manifold is even a shitty one. so basically im just gonna disagree. |
Re: Help me design my build.
Originally Posted by chris
Dont want to burst your bubble but there have been like 3-4 low 11 sec/10 sec d series and those mods are good for maybe high 200's. To run low 11's you need 10g's+ its reality
|
Re: Help me design my build.
if you have money to spend get a b block sleeve it and make 400 whp and you have your low 11's high 10's
|
Re: Help me design my build.
I don't want a b. I want to rock the underdog. :)
|
Re: Help me design my build.
add sleeving to your build. a good size turbo should do the trick. t3/t04e 57 trim should get you into mid to high 300 whp
|
Re: Help me design my build.
I was just going to post it and take my chances, but I am starting to lean more towards sleeves.
|
All times are GMT -5. The time now is 06:33 AM. |
© 2024 MH Sub I, LLC dba Internet Brands