|
b16a wont start please help!!!
I have a b16a in my 91 crx it ran fine forever until the other night i was sitting at a light and it died and hasent started since. The car is getting gas and spark but the spark is a bright orange . I tryied a new dizzy, cheked the timing belt,put new plugs in ,check all my wiring and now im stupped. If any can help please do so Thank you.
|
Re: b16a wont start please help!!!
Do a C/R test dose is sound like it turns over faster then normal?
|
Re: b16a wont start please help!!!
Whats a cr test? and im not sure if it turning over faster, i dont think so
|
Re: b16a wont start please help!!!
compression test
Give us more info nagro |
Re: b16a wont start please help!!!
Thats what i thought but wasent sure thanks
|
Re: b16a wont start please help!!!
compression test . cylinder # 1- 110 psi
2- 96 psi 3- 105 psi 4- 94 psi |
Re: b16a wont start please help!!!
fuelpump went byebye, and you have low compression.
|
Re: b16a wont start please help!!!
its getting gas but i think maybe to much , if the fuel pump is bad will it pump to much gas or no gas at all?
|
Re: b16a wont start please help!!!
regulator limits the fuel, fuelpump supplies teh fuel. ask john maddon to draw this for you.
|
Re: b16a wont start please help!!!
haha you funny guy hahah john madden someone made a funny
|
Re: b16a wont start please help!!!
youve been a hmt member for 3 years, most noobs max your post count in 3 weeks. get with the program
|
Re: b16a wont start please help!!!
if the fuel pump was gone wouldnt it not pump no gas at all
|
Re: b16a wont start please help!!!
Originally Posted by LittleRed88zc
if the fuel pump was gone wouldnt it not pump no gas at all
|
Re: b16a wont start please help!!!
how did you do the compression test those numbers are stupid low. Make sure you pull all the plugs, hook up the gauge, make sure the throttle is open all the way and crank it 4-5 times, and repeat for every cylinder. You should get over 200 psi with a good gauge.
|
Re: b16a wont start please help!!!
no i checked the blinker fluid you lawndart!
|
Re: b16a wont start please help!!!
i will try the c/r test again i dont think we opened up the thottle
|
Re: b16a wont start please help!!!
Originally Posted by LittleRed88zc
no i checked the blinker fluid you lawndart!
Go buy the book for the car and fix that ---- instead of looking for answers here |
Re: b16a wont start please help!!!
did you check your distributor cap and rotor?? I had mine die like that once, it was because i had gotten some moisture inside the cap from it having a shitty old gasket
|
Re: b16a wont start please help!!!
Originally Posted by JDMFantasy2K
how did you do the compression test those numbers are stupid low. Make sure you pull all the plugs, hook up the gauge, make sure the throttle is open all the way and crank it 4-5 times, and repeat for every cylinder. You should get over 200 psi with a good gauge.
Same thing I was gona say. Realy low!!!!! How is your timing belt? Did you jump a tooth or two? |
Re: b16a wont start please help!!!
Originally Posted by ratcityrex
Same thing I was gona say. Realy low!!!!! How is your timing belt? Did you jump a tooth or two? I figured it might be the coil, they usually up and die and will still give you spark in open air. |
Re: b16a wont start please help!!!
Originally Posted by wafflesincars
He didn't have it at WOT.
I figured it might be the coil, they usually up and die and will still give you spark in open air. |
Re: b16a wont start please help!!!
do you guys read? The ignitor is in the dizzy, which he replaced. Main relays do go bad all the ------- time, but it wouldnt have fuel or spark if that was the case. It also says in the first post he checked the t-belt already... Holding the throttle wide open will only give you another 10-15psi. A cyl leakdown test will tell you where the low compression is coming from. Take the schrader valve out of the bottom of your compression tester (you'll need a special screwdriver for this) and hook it right up to an air compressor with the regulator set around 70psi. Pull the dipstick, rad cap, and intake pipe before you hook up the compressor. After you start pumping air into the cyl, listen for leaks at the dipstick, the opened throttlebody, out the back of the muffler, and then look for bubbles in the coolant in the rad.
When you identify your leak(s), heres what is wrong: air coming from- throttle body = bent intake valve(s) exhaust = bent exhaust valve(s) dipstick = beat rings bubbles in the coolant = beat head gasket your lucky im bored... good luck! |
Re: b16a wont start please help!!!
Got it started thanks for all the help from the real people who actually read my first post. Thank you
|
Re: b16a wont start please help!!!
So what was it?
|
Re: b16a wont start please help!!!
timming belt jumped
|
Re: b16a wont start please help!!!
Originally Posted by wafflesincars
Did you check the VTAK fluid?
|
Re: b16a wont start please help!!!
yep it was topped off lol :S
|
| All times are GMT -5. The time now is 03:45 PM. |
© 2024 MH Sub I, LLC dba Internet Brands