TwinTurbo V12 final setting :)
So,after doing it 3 differents way, here is the final one ... "very good flow", no commun firing cylinder in each exhaust pipe.
I did weld it like a pig ... basically,I prefered to tripped all the welding, and then erode itif required. I just tested the all side at 30bars ... no leak. I spend a long long time to make sure I can fit those big ass T04b from Garrett. This set up fit under the hood. I am not happy of the "look of my welding, but I had to mix different kind of standless steel, and some time , it was getting too "sparking" ... I made sure that the penetration is very deep everywhere, it is what matter the most to me ... I don t want to burn the car... I am now cutting a lot of little piece to steel to make heat shields ... I ll wrap the exhaust into a full thermal shield, but additional protection is required for the spark plugs wires. http://www.v12extreme.com/ipost/finalwelding3.jpg http://www.v12extreme.com/ipost/finalwelding2.jpg http://www.v12extreme.com/ipost/finalwelding1.jpg May the Core be with you! That is hand made !!!! :) FrancoisP http://www.v12extreme.com O0 vrooooommmmmmm >:D |
Re: TwinTurbo V12 final setting :)
Pretty sure that is going to make the turbo smoke like crazy. The absolute max you are suppose to tilt a tubo is something like 30 degrees.
Good luck with it though. Later Randy |
Re: TwinTurbo V12 final setting :)
First off, what the ---- are you doing welding in your living room. Your moms going to kill you if you burn down the house. 2ndly, is that thing going to run or just go the stealthmode route and sit on jackstands. If it going to run, you may want to consider sitting the turbo flat for oil drain.
Just kidding about the living room, that fucken rocks. |
Re: TwinTurbo V12 final setting :)
The tillt is really a problem? I was planning to use a separated oil pump to feed them, what do you think?
will it :6 smoke? or damage them? FrancoisP |
Re: TwinTurbo V12 final setting :)
Wow.
HMT v12 bmw??? ??? Where is the wastegate? |
Re: TwinTurbo V12 final setting :)
I ll post the waste gate pic tomorrow.
FrancoisP |
Re: TwinTurbo V12 final setting :)
yeah, that ain't gonna work out very well at all. the oil drain is only gravity fed, and needs to be as straight down as possible
|
Re: TwinTurbo V12 final setting :)
this guy is hardcore, hes got his v12 in his living room on hardwood floors with nigga ass fluxcore welds and turbos hanging off at goofy angles.
Dude, your crazy |
Re: TwinTurbo V12 final setting :)
that thing looks like ---- and that motor is nothing but a cool ass looking paperweight. buy a pushrod v8 and stop mounting turbos half ass calked ------ style sideways upside down that will never work
|
Re: TwinTurbo V12 final setting :)
that flat out will work like ----
|
Re: TwinTurbo V12 final setting :)
Originally Posted by FrancoisP
The tillt is really a problem? I was planning to use a separated oil pump to feed them, what do you think?
will it :6 smoke? or damage them? FrancoisP It will not work like that.. I'm sorry to give you ANOTHER setback. |
Re: TwinTurbo V12 final setting :)
Where do you live man? I just want to know if i might be finding a turbo on the street sometime soon. I doubt those fluxcore welds are going to hold up after everything heats up. What car is this going in anyways?
|
Re: TwinTurbo V12 final setting :)
Hey man, i like the project your taking on and would like to help you do it right. Id love to make some nice stainless steel manifolds at cost for your car. email me at michaeljr@lsdmotorsports.com or pm me for more info. If ive disrespected the fluxcore welds at all, i apologize.
|
no hard feeling :)
I am learning .... so it is not a problem ...
FrancoisP |
Re: TwinTurbo V12 final setting :)
Where's the JB weld? What is this going in anyways? I'm the same as everyone else here about the angle of those turbos. YOu not gonna need a downpipes but upppipe as in smokes stacks and it's gonna be blowing out smoke signals saying "please fix me!" :S :X :S :X :S :6
|
Re: TwinTurbo V12 final setting :)
Originally Posted by FrancoisP
I am learning .... so it is not a problem ...
FrancoisP im the same way dude, if somethin fux up i learn how to fix it |
I think LSD look like a pro, I am thinking giving him the job ... :)
O0 well, probably safer if he does it ... the only problem ... it is not home made any more :y
I ll see if he offer a good price, the cool side of him doing it, I can focus on the electronic part of the project. FrancoisP |
Re: TwinTurbo V12 final setting :)
I'd buy from him, it's still homemade, you're putting it together.
|
Re: TwinTurbo V12 final setting :)
That turbo would last 5 minutes like that before you would ---- up the CHRA
|
All times are GMT -5. The time now is 10:33 AM. |
© 2024 MH Sub I, LLC dba Internet Brands