Some parts to install this weekend.... (pics of course)
 

Well guys I thought I'd make a post because I"m bored.... I'll let everyone know how this system works out when I get it all setup.

http://groups.msn.com/_Secure/0RgCdA...70321597151563

The Greddy Rebic III and Simulator.... this will be the controller for the sub injector system.

http://groups.msn.com/_Secure/0RgDvA...70323913241311

The injector driver, pressure sensor and dropping register for the rebic system

http://groups.msn.com/_Secure/0RgAAA...70321781310217

The harnesses....

http://groups.msn.com/_Secure/0RgDVA...70321973517957

The injector holder/boss I'm using. Its really nice, has a mini fuel rail setup and everything. It better be nice for $65 :(


http://groups.msn.com/_Secure/0RwDjA...70322400814709

Whats the difference between these two injectors..... Oh they may look the same but one is a stock z24/gt injector.... the other is an msd 96# injector. They are identical excluding the pintle holes which are huge on the msd compared to the stocker.

Anyways this should all be setup this weekend and possibly some higher boost levels if it all works out. I used one big injector because it was cheaper going that route opposed to buying another expensive injector holder.

Anyways hopefully this works...again Die FMU DIE DIE DIE :) I should be able to swap back to my stock injectors with this setup too so the car will run better off boost.

Re:Some parts to install this weekend.... (pics of course)
 

wow, looks like you dropped some change. I need to get some bolts so I can put my engine on my engine stand then I'll be a picture ----- just like you. anybody know what thread the bolts are on the tranny side of the engine on a b18?

Re:Some parts to install this weekend.... (pics of course)
 

RICER!!! RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!RICER!!!

ok that took some time to figure out lol ;D was also put up to it lol

Re:Some parts to install this weekend.... (pics of course)
 

Hey bro i couldnt give u the exact #.. However most bolt stores that would carry those, you can take a tranny bolt in and say i need a longer one of these and they should be able to help you. You just need to know its a 17mm and i think its fine thread. Not extra fine but fine, i could be wrong... Go for about 5" long

Re:Some parts to install this weekend.... (pics of course)
 

im pretty sure its a fine thread as well. i forget the exact specs of it tho. if this was a week earlier (or sometime later after i find a new block >:( ) i could let u know

airtonics, looks like some good stuff man, cant wait to hear how it works

Re:Some parts to install this weekend.... (pics of course)
 

problem is all the tranny bolts I have are holding my tranny onto my engine in my car. the ls block isn't too heavy, I might just carry that ---- into carquest and be all, I need a bolt yay long that fits that ----, get on it.

Re:Some parts to install this weekend.... (pics of course)
 

Haha you the man, Take one of those bolts out fool, The tranny has plenty of support, 1 bolt isnt going to do anything.. all else fails dude, You always have your "how to block post" thread to reminiss on.

Re:Some parts to install this weekend.... (pics of course)
 

Thanks for jacking my thread :p


Anyways yeah this setup was more costly than I had planned but oh well.... hopefully it will all be worth it. I just started tinkering with the electronics after getting back from my pre-employment drug test with state farm. Hopefully this beast is all setup today :)

Did I hear someone say 10psi with no timing retard? hehehe

Re:Some parts to install this weekend.... (pics of course)
 

Where the ---- did you get that sub injector rail doo-dad. I spent forever on the net looking for them.

Re:Some parts to install this weekend.... (pics of course)
 

thats pretty neat. looks kinda old school. hahaha. but atleast you'll finally get rid of that damned fmu. good luck