General Discussion Off-Topic Discussion and Enlightenment

engine brake in ?

Thread Tools
 
Search this Thread
 
Old 04-16-2007, 01:24 PM
  #1  
0.5 BAR
Thread Starter
 
99 Si's Avatar
 
Join Date: Jun 2006
Posts: 65
Default engine brake in ?

i recently blew up my stock z6. i have another z6 that is being built (tt rods/vitaras) for my crx but money is tight at the moment so ill be putting that motor in my coupe.

question is, HOW DO I BRAKE THE MOTOR IN ? or better yet, BRAKE IT IN N/A or UNDER BOOST ?



i read this http://www.mototuneusa.com/break_in_secrets.htm and it said to "run it hard." but the motor will be untuned for boost, so should i brake it in n/a ?? or brake it in while tuning for boost ??


lmk what you guys think. thanks.


SETUP:
z6 block w/ tt rods/vitara pistons
pp y8 head w/ stock cam/valve train
ebay t3 "super 60" @ ~ 12psi
stock fuel pump
450cc injectors
stock map sensor

99 Si is offline  
Old 04-16-2007, 01:26 PM
  #2  
3.0 BAR
 
88dx's Avatar
 
Join Date: Nov 2003
Posts: 5,838
Default Re: engine brake in ?

if its not going to be tuned, break it in NA untill u can tune it.
88dx is offline  
Old 04-16-2007, 02:16 PM
  #3  
!! UNCONFIRMED EMAIL !!
 
1991civicsi's Avatar
 
Join Date: Nov 2005
Posts: 1,876
Default Re: engine brake in ?

Originally Posted by 88dx
if its not going to be tuned, break it in NA untill u can tune it.
Also, use conventional oil, and then after a hundred miles change oil and filter. I wouldnt use synthetic until 1000 miles or so.
Breaking the engine in hard is not my choice, but the motor should see da variety of RPM's, I let the motor gain RPM (well before redline) while driving then let off the gas to let the motor slow the car down to bring the idle down low. Repeat.
1991civicsi is offline  
Old 04-16-2007, 02:21 PM
  #4  
1.5 BAR
 
kamilk69's Avatar
 
Join Date: Apr 2006
Posts: 1,147
Default Re: engine brake in ?

ok while were on the subject,

i got a base tune im my car and the afr are around 9.4-9.8, now im building up my new engine 8.7:1 comp ratio the stock car is 9.2:1 but i dont have my tunning software yet. now im thinking that the afr will lean out but by how much, will it be safe to run the engine like that for a month at 8psi untill i buy my tuning software

and btw the software is 350$ fucken rip off but whatever.

and if anyone has a copy of the proracer software for the sct flash unit. hook it up. i better things to spend my money on.
kamilk69 is offline  
Old 04-16-2007, 02:33 PM
  #5  
0.0 BAR
 
Tom-Guy's Avatar
 
Join Date: Feb 2003
Posts: 0
Default Re: engine brake in ?

Motors are best broken in on 20+ psi.
Tom-Guy is offline  
Old 04-16-2007, 02:34 PM
  #6  
3.0 BAR
 
88dx's Avatar
 
Join Date: Nov 2003
Posts: 5,838
Default Re: engine brake in ?

Originally Posted by Joseph Davis
Motors are best broken in on 20+ psi.
88dx is offline  
Old 04-16-2007, 02:43 PM
  #7  
0.5 BAR
Thread Starter
 
99 Si's Avatar
 
Join Date: Jun 2006
Posts: 65
Default Re: engine brake in ?

Originally Posted by Joseph Davis
Motors are best broken in on 20+ psi.
please explain further.
99 Si is offline  
Old 04-16-2007, 02:53 PM
  #8  
0.0 BAR
 
Oscar's Avatar
 
Join Date: Jun 2005
Location: WA
Posts: 0
Default Re: engine brake in ?

Dont break any engine in, NA or boost, if it's not tuned.

Too lean, you ruin your sleeves. Too rich, you ''wash'' out your rings.

Tune for afr's first, then follow the instructions on that website.
Oscar is offline  
Old 04-16-2007, 03:00 PM
  #9  
1.5 BAR
 
kamilk69's Avatar
 
Join Date: Apr 2006
Posts: 1,147
Default Re: engine brake in ?

but is 9.4 - 9.8 too rich
kamilk69 is offline  
Old 04-16-2007, 03:01 PM
  #10  
1.5 BAR
 
darksol2005's Avatar
 
Join Date: Nov 2004
Posts: 1,065
Default Re: engine brake in ?

Are you being sarcastic? I really hope so
darksol2005 is offline  


Quick Reply: engine brake in ?



All times are GMT -5. The time now is 01:35 PM.