Question on oil pan and fitting.
#1
Question on oil pan and fitting.
it seems that the only way to tap my oil pan would be to put the fitting in the shallow end of the pan. Is that ok to put it there? I took the oil pan off and cleaned it out and put 3 1/2 quarts of water in it to see where the oil level was and it's above. The second question is that I have to use a brass barb fitting in order for the line to fit. Is there any other way other than using hondabond or JB weld to attach the fitting to the pan?(Aluminum pan)
#5
Re:Question on oil pan and fitting.
It doesn't even really matter if the return sits below the oil level in the pan. I know it's hard to picture in your head, but pretty much as long as the turbo's oil outlet sits higher than the oil level in the pan, it will drain, even if the drain fitting is tapped into the very bottom of the pan, vertical, does a loop-de-loop, etc.
Drain physics. Don't worry about it.
Matt
Drain physics. Don't worry about it.
Matt
#6
Re:Question on oil pan and fitting.
That was the craziest thing I have ever heard. You contradicted yourself at least twice I think.
Here is the deal. Idealy you want the drain above the oil level. You will live if it is lower, so don't sweat it.
just tap and thread the pan and jb it to seal and call it good.
Here is the deal. Idealy you want the drain above the oil level. You will live if it is lower, so don't sweat it.
just tap and thread the pan and jb it to seal and call it good.
#7
Re:Question on oil pan and fitting.
Originally Posted by Cray91
That was the craziest thing I have ever heard. You contradicted yourself at least twice I think.
Here is the deal. Idealy you want the drain above the oil level. You will live if it is lower, so don't sweat it.
just tap and thread the pan and jb it to seal and call it good.
Here is the deal. Idealy you want the drain above the oil level. You will live if it is lower, so don't sweat it.
just tap and thread the pan and jb it to seal and call it good.
I hate to bring up such an old thread, but you really need to do your research. It works. It's drain physics. It can do a loop de loop, It can go in from the bottom of the pan, and it can be wherever on the pan you'd like it, as long as the TURBOS OIL OUTLET is above the OIL LEVEL IN THE PAN (which would be near impossible for it not to be unless your turbo was on the ground (below the pan). Have you ever looked under your sink? Does your sink drain? How about done a siphon? Does the siphon stop the second the hose in the bucket your filling is under water, or does it work just fine even if the hose stays at the very bottom of the pail? Of course it works, as long as the place you are siphoning from is above the end of the hose. Some setups are better than others, but frankly, you can tap your pan wherever you want.
Matt
#8
Re:Question on oil pan and fitting.
Originally Posted by Johnyquest
I hate to bring up such an old thread, but you really need to do your research. It works. It's drain physics. It can do a loop de loop, It can go in from the bottom of the pan, and it can be wherever on the pan you'd like it, as long as the TURBOS OIL OUTLET is above the OIL LEVEL IN THE PAN (which would be near impossible for it not to be unless your turbo was on the ground (below the pan). Have you ever looked under your sink? Does your sink drain? How about done a siphon? Does the siphon stop the second the hose in the bucket your filling is under water, or does it work just fine even if the hose stays at the very bottom of the pail? Of course it work, as long as the place you are siphoning from is above the end of the hose. Some setups are better than others, but frankly, you can tap your pan wherever you want.
Matt
why does this make no sence to me
Thread
Thread Starter
Forum
Replies
Last Post
baker_jeff
Hybrid/Tech
1
11-01-2006 09:21 PM
KAOS
Forced Induction
16
02-16-2004 01:20 PM
junk240sx
Forced Induction
3
01-30-2004 01:44 PM