need some help plz
Since I’m asking for help I figure I might as well do an introduction
My name is Carl and I live in B.C. Canada 93 civic HB 14 b @ 8 psi with boost creep to 14’ish Dsm bov 450cc injectors with bbks famous tune Fmic with 2.5” charge pipes Custom DP with 2.5” straight pipe (no muffler) Act clutch Custom hmt style manifold Auto meter boost gauge 2” aluminum rad Some chrome catch can Z6 swap with an si trany stock internals 190,000 km so the guy said Ok so I just did the z6 swap on x-mas with the car started and running before new years It started easily and idled / ran nicely, trany was a little bagged on but what can you expect Here’s my problem I think my head is lifting under boost Every time I stop I bleed the coolant system before I shut off my car and refill it before I hit the road It seemed that I got rid of the air bubble in the system after my drive to work Tuesday morning (it was cold, raining low revs no boost drive) On the way home I wanted to test the engine so I broke in to boost (10 psi max no over revving) When I got home my over flow canister was full with coolant sprayed all over the engine bay and there was a lot of air coming out when I was bleeding the cooling system I’ve done this a couple of times and it seems I can get rid of most of the bubble if I drive like a grandma and as soon as I break in to boost I start getting air in to the cooling system I’ve hooked up compressed air to the cylinder and there was no bubbles in the rad (on tdc) I think it was around 100 psi There was milk’ish white fluid about a shot glass worth (I’m guessing water) catch can line coming from the back of the block There was a jelly type paste white’ish green in color in the beginning of the catch can line from the valve cover it smelled and tasted sweet (no I did not eat it) There was very little water in the catch can no oil Yes I am doing research but not every one posts there experiences or tips I am open to any suggestions or advice (smart suggestions) And yes I’m pretty much getting ready to do a head gasket / Arp stud swap oh and my temp sensor never shows over heating also my timing is at 16 and i don't if it should be to be at 18 for the bbk tune iv posted porn before heres the link ill up date it when i get more time https://www.homemadeturbo.com/forum/...?topic=71314.0 |
Re: need some help plz
Originally Posted by Atticus
I’ve hooked up compressed air to the cylinder and there was no bubbles in the rad (on tdc) I think it was around 100 psi
There was milk’ish white fluid about a shot glass worth (I’m guessing water) catch can line coming from the back of the block There was a jelly type paste white’ish green in color in the beginning of the catch can line from the valve cover it smelled and tasted sweet (no I did not eat it) There was very little water in the catch can no oil |
Re: need some help plz
no no when i hooked it up nothing happened that was yesterday
my bad i should of specified that was today when i checked everything again after my drive home which was a slow drive maybe like 4 squirts of air came out of the bleeder screw but after i went around the block hitting 10 psi 2 times for about a second and when i bled it again there was a lot more air i cant figure out if my head is lifting or i still just have an air bubble from the swap |
Re: need some help plz
After the cars warmed up with the radiator cap off dose it constantly have bubbles?
|
Re: need some help plz
I had similar issues with my mustang. Not sure what kind of gaskets are on the hondas but the felpros I had on mustang had paths cut thru the graphite part from the metal cylinder ring to the water hole on both heads. I think when my fuel pump half died at the track, I got some head lifting and the boost sort of cut a path thru the soft part of the gasket. Bottom line was coolant loss and bubbling in the coolant overflow.
Part 2 was replacing stock headbolts with ARP studs and using multi layered steel gaskets. The problem was way reduced. My theory is that I did not get a good seal with the mls gaskets and a stock surface on the heads/block (mls need some super smooth surface prep which I did not do). Part 3 is in progress-back to the felpro graphite gaskets along with the studs. Reassembly almost complete. Erich |
Re: need some help plz
Originally Posted by 88dx
After the cars warmed up with the radiator cap off dose it constantly have bubbles?
The car runs fine like theres nothing wrong I can drive it no problem if I drive slow shift at low rpm and don’t hit boost there dosent seem to be any problems the over flow canister wont fill up and if I bleed the system there is very little air coming out (the bleeder screw by the head where the top rad hose hooks up) if I rev high and/or hit boost my over flow canister fills up and there is a lot of bubbles coming out of the bleeder screw Iv been bleeding and refilling the cooling system for a couple of days now and I still cant get rid of the air. Something tells me that is it was only an air pocket it would have gone away by now |
Re: need some help plz
Not an air pocket. HG problem.
Erich |
Re: need some help plz
ok so today after work i started my car, filled up the rad and played the waiting game
at first there was a bubble coming out of the rad every 30 seconds'ish then when the engine got warm it was about every 5-10 seconds ok so where is the best place to get arp studs fast i have a KP metal head gasket any one know if they are any good i called my local parts dealer they said they had Honda arp studs 1.2 - 1.8 length at 8mm and a pro series 1.8 length at 9mm $40 for the first ones and $100 for the pro series any one know if these will work on my z6 |
All times are GMT -5. The time now is 03:17 PM. |
© 2024 MH Sub I, LLC dba Internet Brands