My Turbo Build (56k Non Friendly)
#1
My Turbo Build (56k Non Friendly)
Just wanna say thanks HMT you guys definitly gave me lots of idea's and helped alot, by getten me cheap parts and getten information by using the search, i know i only have like 4 posts but i have been here a long time, and by using the FAQ's and search you guys helped me out alot with me having to post.
My Car is a 94 cavalier with a 91 beretta gtz Hight Output Quad 4 swapped in it.
-Borla Muffler
-2.5" Mandel Bent Exhaust
-Ross 9.5:1 Forged Pistons (---- You TRS)
-Walbro 255lph High Flow Fuel Pump
-Eagle "ESP" Forged H Beam Rods
-Bored 20 Over
-Perfect Circle Rings
-Clevite 77 Main Bearings
-Clevite 77 Rod Bearings
-ARP Head Studs
-ARP Main Studs
-Reman Head 086
-Felpro Print-O-Seal Headgasket & Engine Gasket Set
-Spec Clutch Stage 3
-AC Delco A/C Delete Pully
-64mm Custom Bored Out Throttle Body
-Clevite New Oil Pump
-Power Gear Timing Tensioner Shoe
-Power Gear Timing Chain & Gears
-Delco Timing Chain Tensioner
-AC Delco Timing Guides All 3
-AC Delco Water Pump Drive & Bearing
-Garrett T3/T04B Turbo .47 Trim Compressor Wheel, 70 A/R Compressor Housing, .63 A/R Turbine Housing
-Tial 38mm Wastegate
-Tial 50mm BOV
-Turbosmart Boost Controller
-Innovative LC-1 Wideband O2 Sensor Meter
-BEGI Adjustable RRFPR
-Accell 38mm Plug Wires
-Neon Coil
-MSD DIS II
-Mopar Super 60 Injectors
-Custom Cobbled Homemade Manifold
-Autometer Electric Fuel Pressure Gauge
-Autometer Electric Oil Pressure Gauge
-Autometer A/F Gauge
-Autometer Boost Gauge
-Jet Adjustable Fuel Pressure Regulator
-ATP Turbo Oil Lines & Fittings & Restrictor
-CCA Intercooler 2.5" In & Out
Thats about all i can think of at this time, the engine bay needs to be cleaned up, same with the interior, wires running enerywheres, but its on the list of too do's. just been breaking it in right now, running about 4psi.
more pics here http://s186.photobucket.com/albums/x...ricklikesbeer/
enjoy
My Car is a 94 cavalier with a 91 beretta gtz Hight Output Quad 4 swapped in it.
-Borla Muffler
-2.5" Mandel Bent Exhaust
-Ross 9.5:1 Forged Pistons (---- You TRS)
-Walbro 255lph High Flow Fuel Pump
-Eagle "ESP" Forged H Beam Rods
-Bored 20 Over
-Perfect Circle Rings
-Clevite 77 Main Bearings
-Clevite 77 Rod Bearings
-ARP Head Studs
-ARP Main Studs
-Reman Head 086
-Felpro Print-O-Seal Headgasket & Engine Gasket Set
-Spec Clutch Stage 3
-AC Delco A/C Delete Pully
-64mm Custom Bored Out Throttle Body
-Clevite New Oil Pump
-Power Gear Timing Tensioner Shoe
-Power Gear Timing Chain & Gears
-Delco Timing Chain Tensioner
-AC Delco Timing Guides All 3
-AC Delco Water Pump Drive & Bearing
-Garrett T3/T04B Turbo .47 Trim Compressor Wheel, 70 A/R Compressor Housing, .63 A/R Turbine Housing
-Tial 38mm Wastegate
-Tial 50mm BOV
-Turbosmart Boost Controller
-Innovative LC-1 Wideband O2 Sensor Meter
-BEGI Adjustable RRFPR
-Accell 38mm Plug Wires
-Neon Coil
-MSD DIS II
-Mopar Super 60 Injectors
-Custom Cobbled Homemade Manifold
-Autometer Electric Fuel Pressure Gauge
-Autometer Electric Oil Pressure Gauge
-Autometer A/F Gauge
-Autometer Boost Gauge
-Jet Adjustable Fuel Pressure Regulator
-ATP Turbo Oil Lines & Fittings & Restrictor
-CCA Intercooler 2.5" In & Out
Thats about all i can think of at this time, the engine bay needs to be cleaned up, same with the interior, wires running enerywheres, but its on the list of too do's. just been breaking it in right now, running about 4psi.
more pics here http://s186.photobucket.com/albums/x...ricklikesbeer/
enjoy
#6
Re: My Turbo Build (56k Non Friendly)
i may have missed it reading through your build list, but what sort of efi ecu do you have?
also, got a shot of the cylinder head? (chamber side) that looks like a sweet motor. i've never seen one before.
fred.
also, got a shot of the cylinder head? (chamber side) that looks like a sweet motor. i've never seen one before.
fred.
Thread
Thread Starter
Forum
Replies
Last Post
Sinner
Engine Management
9
05-24-2004 07:15 PM
Semnos
General Discussion
12
01-07-2004 09:22 PM