Install Pics of my Ls/Vtec Crx
Lots of pics..
https://www.homemadeturbo.com/turbo/lsvtec/fmic.jpg First off, I was using beaus Starion/Conquest intercooler in my Ls/Vtec turbo crx. So I needed to get my own setup. https://www.homemadeturbo.com/turbo/lsvtec/ic.jpg First off I have to thank Tyrus for this sexy piece, we have used his intercoolers before, but we were a bit sure how well this intercooler was going to fit in a 4g. Core Size: 30in (wide) x 5 1/4in (tall) x 2in (deep) End Tanks: 2.25 (wide) x 5 3/8in (tall) x 3in (deep) Piping: 2.5 OD x 1.25 thick / 2.75in Long https://www.homemadeturbo.com/turbo/.../ic/tstfit.jpg On all intercooler installs, you need to start with test fits, It took a few trys to get this thing sitting nice and flush, and aligned perfectly with the bumper. (especially on this car, since it has been wrecked badly in the front end) https://www.homemadeturbo.com/turbo/...ic/compare.jpg Give you an idea what the 2 intercoolers look side by side https://www.homemadeturbo.com/turbo/...c/compare2.jpg You can see that this intercooler has 2.5 inlets, opposed to the starions 2.0in pipes. https://www.homemadeturbo.com/turbo/lsvtec/ic/hack.jpg I didnt want to take a bunch of pics of the hacking, because their was alot, basically we had to cut alot of ---- off the front end, including parts of the core support to bring it up high enough to fit right. We used a sawz all, 5in cutoff wheel and a air hacksaw. https://www.homemadeturbo.com/turbo/...ic/rhmount.jpg As you can see I had to bend the tabs down a little bit so I could get it to mount to the core support. (rh mount) https://www.homemadeturbo.com/turbo/...ic/lhmount.jpg This is the LH mount, just 2 10mm bolts holding the IC in place. https://www.homemadeturbo.com/turbo/.../ic/fitted.jpg Then finally got it mounted, Next step I didnt want to show everyone, because My front bumper is really gay, and I just hacked the living ---- out of it ;) Basically need to cut alot of the plastic off the backside of the front bumper so it fits nice. I kinda cut more than I really needed to. https://www.homemadeturbo.com/turbo/...c/mandrels.jpg A few mandrel bends 2.5 from JC Whitney that we used. https://www.homemadeturbo.com/turbo/...ic/lhupper.jpg This is the upper ic pipe coming off the compressor housing, it goes from 2in imediatly to 2.5in piping, I did have to remove the Washer Bottle/Pump assembly for these pipes to clear. https://www.homemadeturbo.com/turbo/...ic/lhlower.jpg This is the left hand lower section of the IC piping, we used 1 180 and a 90 for this side. The couplers are from Napa, just 2.5 black silicone hose, works perfect! https://www.homemadeturbo.com/turbo/...ic/rhlower.jpg This is the right hand lower side, Very similar to the other side, except I ran out of couplers, so I had to use the sexy yellow piece from a old intake we had. https://www.homemadeturbo.com/turbo/...ic/rhupper.jpg And yes, the hacked up upper IC pipe, this piece has been around along time in a few of my cars, it has been modified many times for different setups, as you can see their is about 40 different welds, hahah, Mounted to the IC pipe, is my Tial Blow off Valve. https://www.homemadeturbo.com/turbo/lsvtec/ic/done.jpg All done https://www.homemadeturbo.com/turbo/lsvtec/ic/race1.jpg It looks very nice.. thanks again Tyrus & thanks to Beau for the sexy tig welds.. Jeff Frank btw, if you guys are interested in one of these coolers check out Tyrus's webpage http://tjn115.tripod.com Email him for current pricing & avalibility |
Re:Intercooler Install Pics of my Ls/Vtec Crx
Damm that looks good, ;D I wish I had all my stuff on my car ???
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
me too.
My damn Waterpump broke :( Man have to take apart a lot of stuff to get to it. getting a new one tomorrow. |
Re:Intercooler Install Pics of my Ls/Vtec Crx
Looks good.
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
You have anything to monitor your intake temps with, see what the raw numbers are for the cooling difference?
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
Looks badass ;D
BTW good write up too!! |
Re:Intercooler Install Pics of my Ls/Vtec Crx
i have one of tyus's intercoolers in my 91 rex. i need pics of it... i did the same damn thing you did when i installed it last summer... to bad i still havent got the car running.... money money money. ill get her goin soon though.
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
Jeff, did you notice any lag or difference between Tyrus's IC and other smaller IC's not as long? Tyrus said on his website people with smaller turbos might notice more lag. I am planning on running a small turbo and 5-7 psi, but if I get hondata I will proly run 8-11 psi. I am guessing it shouldn't be enough of a difference to really matter, but I thought I would ask anyways.
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
Nope, I actually had an improvement.. we upgraded the charge pipes at the same time so maybe that had something to do with it. That starion intercooler that beau has kinda blows ass.
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
nice clean setup and NICE WELDS!
|
Re:Intercooler Install Pics of my Ls/Vtec Crx
Almost 6 months later. That has to be a record. I was wondering how this thread had 9 replies without me seeing it. ::)
__________________ Best Car Insurance | Auto Protection Today | FREE Trade-In Quote |
Re:Intercooler Install Pics of my Ls/Vtec Crx
the welds brought it back ;D
Beau |
Re:Intercooler Install Pics of my Ls/Vtec Crx
Originally Posted by AbaZ
Nope, I actually had an improvement.. we upgraded the charge pipes at the same time so maybe that had something to do with it. That starion intercooler that beau has kinda blows ass.
I still love the intercooler :) |
All times are GMT -5. The time now is 10:31 AM. |
© 2024 MH Sub I, LLC dba Internet Brands