good setup for under 1000
 

ok so today i spun a rod bein. so im think now is the best time and better then ne to do my motor bulid part setting it up for a turbo and i dont have alot of money to spend but i need my car back so i have about a 1000 to spend what are the best set up i would like the motor to be able to hold about 375 hp to 400hp when i end up putting on my turbo
what rods and pistons should i get to set me up for this i was thinking tuner toy rods
oh its a d16y7 and i was lookig on the sponsors for us but could not find any for the d16?

thanks

Re: good setup for under 1000
 

vitara, tt rods and get your crank done

Re: good setup for under 1000
 

i would do the tuner toys but cant find a link with them and a price ?

Re: good setup for under 1000
 

Re: good setup for under 1000
 

there around 200 I think

Re: good setup for under 1000
 

they do not have them d16y7 rods or any for the d all

Re: good setup for under 1000
 

If they dont have them now then they will be in in a week, they sell out all the time

Re: good setup for under 1000
 

but wouldnt they still list that they sold them....i knonw iv seen them on there but i cant find them now

Re: good setup for under 1000
 

found this on e bay what do you guys think its only 295.00 + shipping then ill use the tunertoys when i can find them

Brand New!!!

Honda D16 Civic/CRX Si

Turbo Conversion Kit

Vitara Low Compression Pin Floating Piston Set 8.5:1,

Kits Includes

75mm Low compression Pistons

NPR Chrome Rings

Full Floating Pins and Pin Locks

ACL RACE Rod Bearings

ACL RACE Main Bearings and Thrust washers

Three Layers Metal head Gasket

Silicone Valve Cover Gasket Kit

Pistons are made by Y.C.P. In Japan

Fits Honda ZC, D16A, D16A6, D16Z6, D16Y8, D15B Civic or CRX Si


--------------------------------------------------------------------------------



This Kit includes every part needed to make your D16 N/A engine into a Turbo Beast with New Low Compression Pistons, New ACL RACE High Performance Bearings and New Metal Head Gasket

Tested to over 300 Horsepower with proper fuel and Tuning.

Fits Honda ZC, D16A, D16A6, D16Z6, D16Y8, D15B Civic or CRX Si

Civic/CRX 88-00 V-TEC or Non V-TEC

Pistons can Hold 18-20psi of boost with proper fuel and tuning

These pistons also have Double Holes in the wrist pin bosses to improve oiling and superior lubrication.

Fits Honda ZC, D16A, D16A6, D16Z6, D16Y8, D15B Civic or CRX Si

Re: good setup for under 1000
 

THE D-SERIES RODS ARE CURRENTLY OUT OF STOCK, AS PER OUR CUSTOMERS REQUEST WE HAVE BEEN WORKING WITH OUR MANUFACTURER TO MAKE SOME NEEDED CHANGES TO THESE RODS. SO UNTIL THE CORRECTIONS ARE SATISFIED THESE WILL NOT BE AVAILABLE. WE ARE HOPING TO HAVE THEM IN EITHER THE END OF JANUARY OR THE FIRST PART OF FEBRUARY, PLEASE CHECK BACK WITH US!
via tunertoys.com
ive never had a problem with them. i recieved excellent customer service when i had problems with some a fualty fuel injector and they shipped stuff out like craig walks around with the stuff strapped to his back pachaged at all times living next store to the post office

Re: good setup for under 1000
 

Vitara's, Tuner Toys rods or some used Eagles maybe, 450 or 550cc injectors, hx35, some sort of manifold, and boom, can pull off your HP goal. Oh yeah, ARP head studs.

Re: good setup for under 1000
 

Because you are a n00b, and therefore confused because you haven't heard it thirty times in twenty nine posts: TT rods and Vitaras.

I'd step back to the A6 head with $75 Delta regrind cam, and run an OBX LSD. My head preferrence is a non-issue, but you really should look into an OBX for a serious D-series.

Re: good setup for under 1000
 

have you ever run vitaras before? their sweet for the price but ---- are they noisy little fuckers :(

Re: good setup for under 1000
 

You ran undersized STD Vitaras in oversized STD bores that have tens to a hundred thousand miles worth of wear on them. Yes, YOUR Vitaras are noisy.

Re: good setup for under 1000
 

so then what size piston vitras should i get im boreing my 30 so what should i buy so it is not so loud

Re: good setup for under 1000
 

if your thinkin about boring out a D that far think again just get a good honing and then find a set of vitaras and drop them in O0

Re: good setup for under 1000
 

.5 mm o/s Vitaras are just slightly less than a .5mm o/s in a D15/D16 block. That's more like 0.020", good luck finding Vitaras in 0.030" - not that you'd want to run them in that size with stock sleeves.

Re: good setup for under 1000
 

well my guy at the shop was trowing out an ideal of what size it will be and that was befor it even went to the meachin shop we pulled it out the rest of the way today then i had to leave to flip bugers : ( lol ill know for sure monday

Re: good setup for under 1000
 

right the thoughts are tt rods and some srp pistions