HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Forced Induction (https://www.homemadeturbo.com/forced-induction-7/)
-   -   dyno results are in (https://www.homemadeturbo.com/forced-induction-7/dyno-results-21934/)

Rev2 9K 06-14-2004 12:40 AM

dyno results are in
 
After 5 hours of driving the car is done. After getting the Hondata tuned, the numbers were 200 whp and 179 for torque. All this on 10 lbs. I am happy with it. They blew a half inch hole through 2 of the charge pipe couplers, I thought the motor blew, damn. I will post the pick of the last pull later, then you guys can see how the torque fell when VTEC kicks in, but power goes.

T3/T4 57 trim wheel
450 dsm blue tops
hondata S200 w/boost upgrade
walbro 255 lph pump
MSD 6a with blaster ss coil/ taylor wires
3 " downpipe and exhaust
and a bunch of other stuff to.

leed 06-14-2004 04:44 AM

Re:dyno results are in
 
This on a D? Sound like it. Nice #'s man. Bet it feels nice.
Mind posting a good shot of your graph?

Curious as to how much timing on the top end?


Rev2 9K 06-14-2004 08:08 AM

Re:dyno results are in
 
oh yea, it is a D.I am not sure what they set the timing at. I will post the graph today. By the way, what does everybody's dyno shop charge. I paid $280for a couple of hours.

racinskittle 06-14-2004 02:04 PM

Re:dyno results are in
 
what are the specs on the turbo? (A/R and stuff)

Good numbers BTW! I would have actually expected a bit more, but it was probably a conservative tune. What was the A/F at?

Rev2 9K 06-14-2004 06:41 PM

Re:dyno results are in
 
they were .48/.63 with a 57 trim. It was 10.5, I think that would a little rich correct.

iNetForce 06-15-2004 01:07 AM

Re:dyno results are in
 
would I be able to pull those numbers with a 14b at 10 psi on a z6?

used2baracer 06-15-2004 02:48 AM

Re:dyno results are in
 

Originally Posted by Rev2 9K
they were .48/.63 with a 57 trim. It was 10.5, I think that would a little rich correct.

too rich... u are loosing power and wasting fuel... also, ur torque is falling off due to inadiquate tuning -> pulling back too much timing & running too rich... i bet u will gain 15+ hp by putting some timing back and leaning out a little..

Wildman 06-15-2004 05:47 PM

Re:dyno results are in
 

Originally Posted by iNetForce
would I be able to pull those numbers with a 14b at 10 psi on a z6?

doubt it. i'm not familiar with 14b's that much, but i think they're more along the lines of a t3

Rev2 9K 06-16-2004 08:13 PM

Re:dyno results are in
 
what do you guys use to post pics?

Carnesd 06-16-2004 08:26 PM

Re:dyno results are in
 
www.newbieforces.com

Semnos 06-17-2004 06:14 AM

Re:dyno results are in
 
10.5 is way to rich IMO...get it close to 12 flat and you're good...with a dyno tune they should be able to take it to 12.5 .
But maybe they didn't want you to go past 200 hp on a D-series. They me be scared to blow your engine up.

Rev2 9K 06-17-2004 07:37 AM

Re:dyno results are in
 
yea, probably.

Guy-Fast 06-19-2004 06:46 PM

Re:dyno results are in
 
Defintley tuned on the safe side. Good #'s no reason to push it.

Rev2 9K 06-19-2004 07:16 PM

Re:dyno results are in
 
trying to post results

Rev2 9K 06-19-2004 07:35 PM

Re:dyno results are in
 
[img][/img]

quadnie 06-19-2004 09:37 PM

Re:dyno results are in
 
Nice numbers you got there.

Give me the link and I will edit your posts to reflect the picture.

-ryan


All times are GMT -5. The time now is 06:22 PM.


© 2024 MH Sub I, LLC dba Internet Brands