HomemadeTurbo - DIY Turbo Forum

Page 2 of 3

Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)

- Forced Induction (https://www.homemadeturbo.com/forced-induction-7/)

- - dsm problems.... (https://www.homemadeturbo.com/forced-induction-7/dsm-problems-28544/)

MetalJim

10-21-2004 09:44 PM

Re:dsm problems....

Does the shaft spin freely?

hybrdcivic95

10-22-2004 05:54 AM

Re:dsm problems....

yea, no play at all

Donald125

10-22-2004 12:51 PM

Re:dsm problems....

so did u check the WG yet?

turboDA6

10-22-2004 02:05 PM

Re:dsm problems....

Quote:

Originally Posted by ghettoturbo

Quote:

Originally Posted by turboDA6

if the flapper is closed it will generate 0 boost... no matter how hard u try. not even barely 1... close the flapper arm and check the wastegate to make sure its holding it closed...

lol, the first part is backwards

hah.. oops... i meant if its open... dude i think ur wg is crapped out... its like so ------ weak it opens to easily even if the flapper is closed. either shorten the rod or get a new wg

hybrdcivic95

10-22-2004 08:47 PM

Re:dsm problems....

i checked the wastegate...it has tension on it when i pull on it, so i dont think thats it

robs99si

10-22-2004 09:47 PM

Re:dsm problems....

Quote:

Originally Posted by trebor_nordap

check to see if the gasket betweeb the compressor housing and the center section is good or is there at all. you'll have to remove the compressor housing.

uh...^^^

turboDA6

10-23-2004 02:55 AM

Re:dsm problems....

Quote:

Originally Posted by trebor_nordap

Quote:

Originally Posted by trebor_nordap

check to see if the gasket betweeb the compressor housing and the center section is good or is there at all. you'll have to remove the compressor housing.

uh...^^^

i was gonna say the same thing... mr hybrid... take off the vacume line to the wg and see if it creates any boost... jus dont over boost. if it does create some boost then ur wg is ----... i still think its ur wg cuz ur turbo has zero shaft play... jus cuz it has tention doesn't mean it aint gonna open early with vacume source... cmon man try it and work with us... were tryin to help =x

turboDA6

10-24-2004 09:33 PM

Re:dsm problems....

look what i found for you... from the man him self

Quote:

Originally Posted by AbaZ

running out of steam at 6100? I'm telling you guys, its those gay ass wastegate actuators on those things that make the 14b's feel like ----. Take the wastegate actuator off, throw a carb spring on and just go drive it, tell me what you think.

dsm	10-30-2004 10:06 PM

Re:dsm problems....

Quote:

Originally Posted by turboDA6

if the flapper is closed it will generate 0 boost... no matter how hard u try. not even barely 1... close the flapper arm and check the wastegate to make sure its holding it closed...

you sir are a moron...you need to be posting on midgatuners.com

turboDA6

10-31-2004 05:34 AM

Re:dsm problems....

Quote:

Originally Posted by dsm

Quote:

Originally Posted by turboDA6

if the flapper is closed it will generate 0 boost... no matter how hard u try. not even barely 1... close the flapper arm and check the wastegate to make sure its holding it closed...

you sir are a moron...you need to be posting on midgatuners.com

you sir are an idiot... i corrected my self as well as many others correcting me... mr "i got 2 post" lmfao. u need to quit posting and leave the site before i stick my dick in ur ass

All times are GMT -5. The time now is 11:46 AM.

Page 2 of 3

Show 40 post(s) from this thread on one page