new header for the 22r... and a downside to welding in flannel
 

https://img.photobucket.com/albums/v...x/IMG_0218.jpg
stock piece of ----
https://img.photobucket.com/albums/v...x/IMG_0219.jpg
new header from a total of 2 180º bends cut into 2 peices
Attachment 28794
and what happens when you wear flannel when welding.

i wasn't even welding, i walked away to go dunk the header in some water, and im like wtf, my leg is warm?

i look down to find my shirt on fire. dampened it out while trying to rip it off (tip: snap buttons only, not hole buttons will aid in this), got it out, still had it on, then realized that the melted plastic had caught my pants on fire. bout the size of a cd case where its red (first degree) and only one spot where hot molten plastic gave me 2nd degree burns

Re: new header for the 22r... and a downside to welding in flannel
 

LOL!!!!

"wtf, my leg is warm"..

Re: new header for the 22r... and a downside to welding in flannel
 

yeah, sucks sitting, jeans pull across it.

touching it = ow

ill post back when my leg ganggreens and falls off

Re: new header for the 22r... and a downside to welding in flannel
 

Liar, liar, pants on fire... ------. :X

Re: new header for the 22r... and a downside to welding in flannel
 

At least your header turned out fairly decent... Also, welding in 100% cotton is recommended.

Re: new header for the 22r... and a downside to welding in flannel
 

it was cotton flannel...

i dont understand why it caught on fire.

Re: new header for the 22r... and a downside to welding in flannel
 

https://img.photobucket.com/albums/v...x/IMG_0221.jpg
https://img.photobucket.com/albums/v...x/IMG_0222.jpg
https://img.photobucket.com/albums/v...x/IMG_0223.jpg
https://img.photobucket.com/albums/v...x/IMG_0224.jpg

and a crappy vid
http://img.photobucket.com/albums/v3...h_MVI_0225.jpg

Re: new header for the 22r... and a downside to welding in flannel
 

Mani looks good.

Next time keep a glass of water by you, just in case ;) haha

Re: new header for the 22r... and a downside to welding in flannel
 

That looks way too close to the nutsack. :o That could have been much worse. :l
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote

Re: new header for the 22r... and a downside to welding in flannel
 

youre tellin me

Re: new header for the 22r... and a downside to welding in flannel
 

If you know your on fire, your not concentrating enough on what your welding. I got a nice hole in my Honda work jacket from welding ----.

Re: new header for the 22r... and a downside to welding in flannel
 

eh, once he heals it'll just be easy access pants for his girly

Re: new header for the 22r... and a downside to welding in flannel
 

I love your yota c0mpl3x. Yotas are tits.

Damn that was a close call.

Re: new header for the 22r... and a downside to welding in flannel
 

true that. The good news is that the manifold looks neat. Nice work man.

Re: new header for the 22r... and a downside to welding in flannel
 

ill try to get some pics with the parents ebay camera next time im around there, .1mp more than mine and it comes out crystal clear. good lesson: bigger the lens, better the pictures, megapixels dont mean ----

Re: new header for the 22r... and a downside to welding in flannel
 

http://img.photobucket.com/albums/v3...x/P1050205.jpg
http://img.photobucket.com/albums/v3...x/P1050206.jpg
http://img.photobucket.com/albums/v3...x/P1050207.jpg
http://img.photobucket.com/albums/v3...x/P1050208.jpg
http://img.photobucket.com/albums/v3...x/P1050210.jpg
http://img.photobucket.com/albums/v3...x/P1050211.jpg

Re: new header for the 22r... and a downside to welding in flannel
 

not rust on my frame/hanger, it's a shitty ziebart undercoat job. surface only on it

Re: new header for the 22r... and a downside to welding in flannel
 

Where the ---- is the turbo?

Re: new header for the 22r... and a downside to welding in flannel
 

it got burned in the flannel fire

Re: new header for the 22r... and a downside to welding in flannel
 

missing right now. i need elec fuelpump + 1:1 fmu + carb mods + turbo + manifold.

along with boost gauge.

i have, none of the above.

thats where your turbo is ;)

Re: new header for the 22r... and a downside to welding in flannel
 

where you pick up the header flange?

Re: new header for the 22r... and a downside to welding in flannel
 

http://www.toyotacatalog.net/M1WebGe...6-70E281AD9F38

Later
Randy

Re: new header for the 22r... and a downside to welding in flannel
 

$30 junkyard header off of a 1981 toyota 4x4 that had the truck rolled on its side

Re: new header for the 22r... and a downside to welding in flannel
 

you make me anna go out and buy a damn toyota pick up.. ---- !!!! your "cold air intake" is ghetto-fabulous :y

Re: new header for the 22r... and a downside to welding in flannel
 

its much quieter than the donut element oem filter. plus it flows better. a little jbweld on the choke rod hole and a thicker rubber gasket its its boost ready

Re: new header for the 22r... and a downside to welding in flannel
 

Same thing happened to me welding the upper hoop on the cage. I stop, flip my helmet up, and i'm thinking that the weld is putting off a lot of heat. I could feel it on my face. Looked down and my shoulder was on fire.

Re: new header for the 22r... and a downside to welding in flannel
 

God damn thats alot of rust!

Re: new header for the 22r... and a downside to welding in flannel
 

stupid ----, i said it wasn't rust.

ziebart undercoat = worst in the world. id have better luck driving into 5gal buckets of roofing tar at 65mph to undercoat my truck and have it last, than have it ziebarted. btw, it came ziebarted when i bought it

Re: new header for the 22r... and a downside to welding in flannel
 

The good thing about cotton is that it doesn't melt when it burns. Imagine if you had polyester on and it caught fire. It would melt to your skin. That's why cotton is reccomended.

Re: new header for the 22r... and a downside to welding in flannel
 

haha nice work man.. thumbs up, just missing aturbo ;)

Re: new header for the 22r... and a downside to welding in flannel
 

turbo and bends en route to my house. flange bov and charge piping already here