HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Engine Management (https://www.homemadeturbo.com/engine-management-10/)
-   -   vafc crap new problems (https://www.homemadeturbo.com/engine-management-10/vafc-crap-new-problems-74965/)

ososlohatch 03-14-2007 04:01 PM

Re: vafc crap
 
i just switched the white and yellow wires some kid on h-t said that the book was wrong and apex never released the info,l i did it and it worked fine, but then my car went to rich then lean and died, now it has no fuel [pressure and wont start. i'm either out of gas or fuct my fuel pump by running it without the injectors tuned down. i have tomorrow off ill look into some more then

2poor2tune 03-14-2007 05:46 PM

Re: vafc crap
 
yay i got it to work today and just in case anyone was wondering its c11 for the map signal wire. i forget which wire i put on what side of the harness but it worked. turbo time. hahaha.

ososlohatch 03-14-2007 07:12 PM

Re: vafc crap
 
good news

imburne 03-14-2007 07:13 PM

Re: vafc crap
 

Originally Posted by Joseph Davis
Rock an FMU

lmao! Thats wild!

ososlohatch 03-22-2007 01:46 PM

Re: vafc crap new problems
 
well i have the 390's in now(gray tops) tuned down 50% from like 1000-3000 on low throttle to have a normal afr at idle but im still running pretty rich, wide band fluxuates (spl) from 12.5:1 - 13.2:1 at idle, that seems pretty rich for idle, fuel pressure is at 40 on the rail and 35 on the return is it normal for it to run so rich at idle ?? or could it possibly be that my wideband is place to close (about 10 inches from exhaust housing) ? thanks for any help. p.s. also wondering if the gray top dsm injectors are high impendence or lo impendence

HMTguy 03-22-2007 02:28 PM

Re: vafc crap new problems
 
Your wideband placement is fine, mine is about 5 inches from the exhaust housing.

Hitchhikkr 03-22-2007 02:31 PM

Re: vafc crap new problems
 

Originally Posted by ososlohatch
p.s. also wondering if the gray top dsm injectors are high impendence or lo impendence

Pretty sure 390's are low imp. so resistor pack is your friend. :P

ososlohatch 03-22-2007 02:38 PM

Re: vafc crap new problems
 

Originally Posted by Hitchhikkr
Pretty sure 390's are low imp. so resistor pack is your friend. :P

factory honda resistor box is installed it obd-o mpfi stock clips

ososlohatch 03-22-2007 06:17 PM

Re: vafc crap new problems
 
also what should the v/t unmt be set at if vtecs at 5000 ??low % ? and high % ?

Slo_crx1 03-22-2007 09:03 PM

Re: vafc crap new problems
 
Stock pr3's are usually around the 45-4600 mark, so I really wouldn't bother with a unmatch setting if you set it at 5000. If it presents a problem you'll see your wideband go rich from 4600 to 5k and then go normal. You can dial it out then if it really bothers you. Just out of curiosity, how far did you retard the timing at the dizzy? Might have an incomplete combustion if it's too far retarded making it seem like it's still rich.


All times are GMT -5. The time now is 02:45 PM.


© 2024 MH Sub I, LLC dba Internet Brands