tuning questions for evo turbo zc
in the works is *project zc8* im using a a TD05HR from a usdm evo 8 450cc dsm injectors,cca intercooler,255lph walbro,2.5 charge piping. 3" downpipe and catback, and an unknown manifold as i don't have one yet and am currently looking but i may have to fab one myself. my question is
does anyone have tuning tips for a set up similar to this? maybe someone running a 16g.what should i see as far as spool characteristics etc. im looking to boost 8 on the streets and 15 when needed. all this on built internalls(no sleeving just block posting). any advice and tips are welcome. help a noob out fyi none of this stuff has been installed yet but i have most everything except for the intercooler and lines and connectors |
Re:tuning questions for evo turbo zc
project "dildo up the ante"
|
Re:tuning questions for evo turbo zc
besides the fact that you are a hatin ass homo.....why do you say that?(prove me wrong)
Originally Posted by Ravage70
project "dildo up the ante"
|
Re:tuning questions for evo turbo zc
I have a 16G on my d16z6. My bin is good for around 10lbs. It is in the bin depository. It is nice and rich in boost, for me atleast. There hasn't been any part throttle tuning though, just WOT running a stock O2 sensor.
Oh, the waste gate you will want will be off a 14b, it will get you to 9lbs. And then you can play with it from there, stock 16g wastegates are like 13 or so. |
Re:tuning questions for evo turbo zc
Doesnt the EVO8 run like 20-22 psi of boost stock?
|
Re:tuning questions for evo turbo zc
They use a boost solenoid to turn the boost up. That is how all the eclipses are. And I think it is up there 18-20. Which is pretty nice for a stock car. The only gay thing is the exhaust flange on the evo 8, it is unlike all of the other 16g. >:(
|
Re:tuning questions for evo turbo zc
I have an Evo III big 16g on d15b2 with mpfi. I have a very similar set up. I'm running a pm6 map recurved for 450's. My management is zdyne. I'm very happy with the turbo. I've also used it on a built d16a6. You can pm me if you got any questions.
Originally Posted by 93turbo16
Oh, the waste gate you will want will be off a 14b, it will get you to 9lbs. And then you can play with it from there, stock 16g wastegates are like 13 or so.
|
Re:tuning questions for evo turbo zc
well what i was wondering is do i need to have 2 seperate bins on seperate chips to boost 8-9 psi and then another to go to 15-20 psi? or do i have one bin and have it be rich to compensate. also is it better to create the map in linear mode or in steps i want to start out with a bin. that i can drive on daily with out worry until i get to the dyno. and last question is....should i hold off on installing the turbo until i break my motor in or just do everything at once. will boost effect the break in? not to say im going to be flooring it day one but i mean for everyday driving
|
Re:tuning questions for evo turbo zc
Just tune it for 15-20 and you should be fine for anything lower.
Oh the 14Bs have 8-10 PSI wastegates, and the 16Gs are higher. I a 14b gate off my dad's stock turbo and put it on my 16G. I know the 16G is atleast 13 because that is where it was going to and I asked around, and came up with somewhere between 11-13 for the 16g and like 8-10 on the 14b. Maybe you have a 14B gate on it, or the older 16Gs just have smaller gates. But mine wasn't a stock turbo either. |
Re:tuning questions for evo turbo zc
Originally Posted by 91efate
should i hold off on installing the turbo until i break my motor in or just do everything at once. will boost effect the break in? not to say im going to be flooring it day one but i mean for everyday driving
|
All times are GMT -5. The time now is 11:24 PM. |
© 2024 MH Sub I, LLC dba Internet Brands