Trying to make Freelog work with LM-1 and crome free??
#1
Trying to make Freelog work with LM-1 and crome free??
I have tried to setup the LM-1 to work with freelog but i am still not getting any results. When i turn the car on it shows things working on the live data screen. i get things moving around different settings etc. but i do not get any cells being filled in on the screen.
Ill try and make this simple to understand:
Im using crome free version. + freelog + LM-1 programmer.
Can you tell me what the settings are on the Lm-1 programmer.
I have set as following:-
In Analog Output 1 i have used air-fuel-ratio
1 volt = 10 AFR and
2 volt = 20 AFR
That is all i have set in the Analog output 1 box.
I have used the red wire from Aux output as described in the instruction manual and wired it to D14.
On Freelog I have gone to settings> wideband and entered the following:
Volt 0 afr 7.35
Volt 3.25 afr 22
In settings formula changed 02 to wideband.
In the main table I have matched the freelog tables to crome in both map scaler + rpm.
In Comms I have it set to port com 3
Baudrate, 9600, databits 8, parity N, stopbits 1. These were all automatic settings.
I have set the driver on my pc to com port 3 so it matches.
I cannot think of what I am doing wrong as I have tried and read lots of posts on this but I just cannot figure it out..
Can anyone suggest where I am going wrong.
I have the crome chip set with datalog + RTP added + remove check sum + disable 02 ticked and saved.
Any ideas??
Ill try and make this simple to understand:
Im using crome free version. + freelog + LM-1 programmer.
Can you tell me what the settings are on the Lm-1 programmer.
I have set as following:-
In Analog Output 1 i have used air-fuel-ratio
1 volt = 10 AFR and
2 volt = 20 AFR
That is all i have set in the Analog output 1 box.
I have used the red wire from Aux output as described in the instruction manual and wired it to D14.
On Freelog I have gone to settings> wideband and entered the following:
Volt 0 afr 7.35
Volt 3.25 afr 22
In settings formula changed 02 to wideband.
In the main table I have matched the freelog tables to crome in both map scaler + rpm.
In Comms I have it set to port com 3
Baudrate, 9600, databits 8, parity N, stopbits 1. These were all automatic settings.
I have set the driver on my pc to com port 3 so it matches.
I cannot think of what I am doing wrong as I have tried and read lots of posts on this but I just cannot figure it out..
Can anyone suggest where I am going wrong.
I have the crome chip set with datalog + RTP added + remove check sum + disable 02 ticked and saved.
Any ideas??
#2
Guest
Posts: n/a
Re: Trying to make Freelog work with LM-1 and crome free??
Well first off.. Do you have J12 cut?
I have mine setup like this and it works ****.
IN FREELOG SETTINGS WIDEBAND
Voltage AFR
0.1 7.35 make sure your LM-1 anolog out that is connected to d14 has the slope set the same as this.
3.25 22
IN FREELOG SETTINGS FORMULAS
then go to Formulas O2 and change the setting to wideband TBL
I have mine setup like this and it works ****.
IN FREELOG SETTINGS WIDEBAND
Voltage AFR
0.1 7.35 make sure your LM-1 anolog out that is connected to d14 has the slope set the same as this.
3.25 22
IN FREELOG SETTINGS FORMULAS
then go to Formulas O2 and change the setting to wideband TBL
#3
Re: Trying to make Freelog work with LM-1 and crome free??
I do have J12 cut.
I think the com port settings might have been wrong as i tried it late last night after changing alot of things and i got the loop back test to work!! + the sanity check. Then went to start he rex and the battery was flat. Ill let you know if i get it sorted but it will not be until end of the week due to wrk commitments!!
I think the com port settings might have been wrong as i tried it late last night after changing alot of things and i got the loop back test to work!! + the sanity check. Then went to start he rex and the battery was flat. Ill let you know if i get it sorted but it will not be until end of the week due to wrk commitments!!
Thread
Thread Starter
Forum
Replies
Last Post
krustindumm
Turbo Parts For Sale
7
02-01-2009 06:48 PM
CLE
Engine Management
9
11-04-2007 12:50 PM