Engine Management eCtune , Crome , AFC , FMU , Zdyne , Hondata , EMS , TE , Uberdata Anything to control your fuel, spark needs!

TE 2.5.5 + Ostrich Problem HELP...

Old 05-17-2006, 03:53 PM
  #1  
0.5 BAR
Thread Starter
 
Join Date: Feb 2006
Posts: 52
Default TE 2.5.5 + Ostrich Problem HELP...

I have just updated the TE from 2.5.2 to 2.5.5 by downloading the .exe file from pgmfi and replace the exe of the ver 2.5.2. I have checked the com no. they are correct set as com 4. I have also done the setting as said on moates.net where setting the the bit/sec to 115200 and latency to 1. (I am trying to link it up with the ECU out of the car via my laptop). However this is what I am getting when I try the real time programming: -

*** Loading RTP environment..
*** Programmer: 2 COM: 4 Settings: 115200,n,8,1
*** --> Setting Baud Rate
*** --> Setting Read/Write Bank
*** --> Setting Emulation Bank
*** Looking for Ostrich..
*** Ostrich v10.10. Found!
*** Synronizing ROM to Ostrich..

Then since nothing happening I close the RTP window that poped up and try again... this appears: -

*** Loading RTP environment..
*** Programmer: 2 COM: 4 Settings: 115200,n,8,1
*** --> Setting Baud Rate
*** --> Setting Read/Write Bank
*** --> Setting Emulation Bank
*** Looking for Ostrich..
*** Version Request Error?! (0x3F)
*** Ostrich v10. Found!
*** Synronizing ROM to Ostrich..

Notice the verseion request error.. Any one got any ideas I can try
gary_yuen42 is offline  
Old 05-17-2006, 05:01 PM
  #2  
1.0 BAR
 
Join Date: Feb 2004
Posts: 577
Default Re: TE 2.5.5 + Ostrich Problem HELP...

Not sure about the version error, but when you launch the rtp it will first synchronize the map that you have open with TE on the ostrich and then wait for you to do changes. That's why you saw nothing happening, try doing some changes to your map or changing the rom property, the rtp monitor will give you feed back about TE writing on ostrich. This is as long as TE found ostrish.

EDIT: Check the TE sticky at top, there is an updated version on TurboEdit.
n2o_2k is offline  
Old 05-17-2006, 05:10 PM
  #3  
0.5 BAR
Thread Starter
 
Join Date: Feb 2006
Posts: 52
Default Re: TE 2.5.5 + Ostrich Problem HELP...

I see... Just tried that there at least something is happening although got a error message : -

*** Byte write error! No changes mande! (0x3F)
*** Byte write error! No changes mand

Also updated to V2.6.1 as well

gary_yuen42 is offline  
Old 05-17-2006, 05:28 PM
  #4  
1.0 BAR
 
Join Date: Feb 2004
Posts: 577
Default Re: TE 2.5.5 + Ostrich Problem HELP...

Not sure about that error, try to restart your laptop, corrupted driver maybe .
n2o_2k is offline  
Old 05-17-2006, 08:52 PM
  #5  
0.5 BAR
Thread Starter
 
Join Date: Feb 2006
Posts: 52
Default Re: TE 2.5.5 + Ostrich Problem HELP...

Tried restarting no luck..... anyone
gary_yuen42 is offline  
Old 05-17-2006, 09:21 PM
  #6  
1.0 BAR
 
Join Date: Apr 2004
Posts: 240
Default Re: TE 2.5.5 + Ostrich Problem HELP...

I haven't seen your specific issue... but how hold is your Ostrich? Could be an improper firmware problem. Also confirm you are on the right com ports.

Also, go ahead and get ahold of 2.6.3 from the pgmfi.org thread... its got datalogging
splitime is offline  
Old 05-17-2006, 10:46 PM
  #7  
0.5 BAR
Thread Starter
 
Join Date: Feb 2006
Posts: 52
Default Re: TE 2.5.5 + Ostrich Problem HELP...

The ostrich, I just bought it brand new, open the casing it said V1.60. Firmware I checked it is 10.10.o also tried firmware 10.3.0 as well. I have the right port com as well as when I tried RTP, it can find the ostrich ok also checked on device manager to confirm.

Also i only seems to able to find 2.6.1 version of TE.... and I got that installed as well.
gary_yuen42 is offline  
Old 05-18-2006, 01:10 AM
  #8  
1.0 BAR
 
Join Date: Apr 2004
Posts: 240
Default Re: TE 2.5.5 + Ostrich Problem HELP...

http://www.tunerpro.net/registration.htm

Use this software to confirm you can connect successfully with the Ostrich, it'll detect it on startup... if it doesnt... that rules out TE sorta.
splitime is offline  
Old 05-18-2006, 01:45 PM
  #9  
0.5 BAR
Thread Starter
 
Join Date: Feb 2006
Posts: 52
Default Re: TE 2.5.5 + Ostrich Problem HELP...

Ok downloaded the Tunerpro RT, Opened a NG60_18 bin... although nothing displayed but I went on choose display 3D graph, then a graph came up so I assume it loaded ok.

The TunerPro RT also recognise the Ostrich, then I went to emulation, and upload the bin to ostrich. It uploaded ok, then I went to verify option it also verify ok using tunerpro RT. That i guess confirm that the ostrich is talking ok with Tunerpro.... however the problem is that the error message from TE V2.6.1. Anyone ?
gary_yuen42 is offline  
Old 05-19-2006, 10:05 AM
  #10  
1.0 BAR
 
Join Date: Apr 2004
Posts: 240
Default Re: TE 2.5.5 + Ostrich Problem HELP...

Originally Posted by gary_yuen42
The TunerPro RT also recognise the Ostrich, then I went to emulation, and upload the bin to ostrich. It uploaded ok, then I went to verify option it also verify ok using tunerpro RT. That i guess confirm that the ostrich is talking ok with Tunerpro.... however the problem is that the error message from TE V2.6.1. Anyone ?
Going on this, looks like it is working... so thats a good sign.

Check to confirm your port settings in TE options are correct.
splitime is offline  

Thread Tools
Search this Thread
Quick Reply: TE 2.5.5 + Ostrich Problem HELP...


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.