OBD0 to OBD1 conversion help!!!!!
http://www.-------------/install/OBD0-OBD1.htm
Double check all connectors and start it up. You will need to re-pin the OBD1 distributor to match the (88-91) OBD0 plug as well. This step is fairly easy. Just match all the colors up. There should be 2 white wires that are on the OBD0 distributor plug and only one on the OBD1/2 plug and an extra yellow/green. The larger of the two white wires on the OBD0 side needs to go to the yellow/green wire on the Obd1 side. Therefore, the smaller white wire on the OBD0 side needs to go to the white wire on the OBD1 side. Basically you want to have 2 of the like plugs, either male and female OBD0 or OBD1. You can also cut and solder on the new plugs. one white wire runs with all the other wires of the dizzy.... the other runs back into the conduit.. seprete from the other wires.. i ASSume the seprete wire is the larger one but to me they both look the same :( http://www.t-mobilepictures.com/phot...gpncejoipg0lo3 |
Re: OBD0 to OBD1 conversion help!!!!!
|
Re: OBD0 to OBD1 conversion help!!!!!
Get a new camera, damn your phone sucks.
|
Re: OBD0 to OBD1 conversion help!!!!!
Originally Posted by jagojon3
Get a new camera, damn your phone sucks.
didnt read it... but from the last shitty pic im gonna say try it one way, if it dont work, it should be the other way... |
Re: OBD0 to OBD1 conversion help!!!!!
Originally Posted by turbohf
:y
didnt read it... but from the last shitty pic im gonna say try it one way, if it dont work, it should be the other way... |
Re: OBD0 to OBD1 conversion help!!!!!
tracing the wiring back through the harness.. one of the white wires doesnt go with the others..
http://www.t-mobilepictures.com/phot...oo06wmz9pfwd3j says the thicker white wire is for icm.. would it make sense for that wire to run seprete from the others? http://i29.tinypic.com/2lxcadu.jpg does that mean the thicker white wire is the one that runs alone |
Re: OBD0 to OBD1 conversion help!!!!!
Originally Posted by buk9tp
i read that it can fry your dizzy if you get the wires wrong :(
disclaimer: your a dumbass for listening to me if you ---- your ---- up :-* |
Re: OBD0 to OBD1 conversion help!!!!!
omg... grab a volt meter... test which is which...
ICM = B15 (PR3) CYP M = B12 (PR3) |
Re: OBD0 to OBD1 conversion help!!!!!
ok bear with me now..
first the unmolested wiring diagram which i will only link to.. http://i32.tinypic.com/2s9t0l3.jpg then the wiring diagram i drew over.. pointing out the 6 wires which are together with the white wire.. and the other white wire which goes alone which is connected to the icm.. therefore i came to the conclusion that the white wire which goes alone into the harness is the thicker one since it goes to the icm.. therefore that white wire will be connected to the yellow wire on the obd1 side.. and the thinner white wire which goes in with the other wires will be connected to the other white wire on the obd1 side.. make sense???? http://i28.tinypic.com/2wps8rb.jpg |
Re: OBD0 to OBD1 conversion help!!!!!
|
All times are GMT -5. The time now is 01:15 AM. |
© 2024 MH Sub I, LLC dba Internet Brands